People | Locations | Statistics |
---|---|---|
Naji, M. |
| |
Motta, Antonella |
| |
Aletan, Dirar |
| |
Mohamed, Tarek |
| |
Ertürk, Emre |
| |
Taccardi, Nicola |
| |
Kononenko, Denys |
| |
Petrov, R. H. | Madrid |
|
Alshaaer, Mazen | Brussels |
|
Bih, L. |
| |
Casati, R. |
| |
Muller, Hermance |
| |
Kočí, Jan | Prague |
|
Šuljagić, Marija |
| |
Kalteremidou, Kalliopi-Artemi | Brussels |
|
Azam, Siraj |
| |
Ospanova, Alyiya |
| |
Blanpain, Bart |
| |
Ali, M. A. |
| |
Popa, V. |
| |
Rančić, M. |
| |
Ollier, Nadège |
| |
Azevedo, Nuno Monteiro |
| |
Landes, Michael |
| |
Rignanese, Gian-Marco |
|
Cabibbo, M.
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (30/30 displayed)
- 2024Effects of Direct Aging Heat Treatments on the Superelasticity of Nitinol Produced via Laser Powder Bed Fusioncitations
- 2024Short-term creep approach to redefining the role of 17-4PH stainless steel for high-temperature applications
- 2024The role of the preparation route on microstructure and mechanical properties of AlCoCrFeNi high entropy alloycitations
- 2023Direct monitoring of porosity evolution by dynamic modulus measurements: Three case studiescitations
- 2023Static and dynamic precipitation phenomena in laser powder bed-fused Ti6Al4V alloycitations
- 2023Study on the mechanical properties of magnetron sputtered W-based degradable radiopaque coatings for tiny biodegradable metallic endovascular implantscitations
- 2022Mechanical spectroscopy study of as-cast and additive manufactured AlSi10Mgcitations
- 2022Creep response of Ti–6Al–4V alloy produced by additive manufacturing: Effect of annealing at 1050 °Ccitations
- 2022Residual stresses in the graded interlayer between W and CuCrZr alloycitations
- 2022On the creep performance of the Ti‐6Al‐4V alloy processed by additive manufacturingcitations
- 2021Laser defocusing effect on the microstructure and defects of 17-4ph parts additively manufactured by slm at a low energy inputcitations
- 2021Modelling the creep behavior of an AlSi10Mg alloy produced by additive manufacturingcitations
- 2021Effect of alloying elements on the properties of Ti-Al-Si alloys prepared by powder metallurgycitations
- 2020Carbon content driven high temperature γ-α2 interface modifications and stability in Ti–46Al–4Nb intermetallic alloycitations
- 2020Minimum necessary strain to induce tangled dislocation to form cell and grain boundaries in a 6N–Alcitations
- 2020High-strength ultrafine-grained CoCrFeNiNb high-entropy alloy prepared by mechanical alloying: Properties and strengthening mechanismcitations
- 2019The role of advanced materials in the development of innovative manufacturing processes
- 2018Indentation strain rate sensitivity of ball-milled spark-plasma sintered Cu-C metal matrix compositecitations
- 2016A Review on Fatigue Life Prediction Methods for Metalscitations
- 2016Constitutive analysis of high-temperature workability of a high-nitrogen bearing steelcitations
- 2015Mechanical properties and microstructure of primary and secondary AA6063 aluminum alloy after extrusion and T5 heat treatmentcitations
- 2015Mechanical and microstructure characterization of hard nanostructured N-bearing thin coating
- 2014Double side friction stir welding of AA6082 sheets: Microstructure and nanoindentation characterizationcitations
- 2014Advanced Hard Coatings: Towards A Whole New World
- 2014High temperature thermal stability of innovative nanostructured thin coatings for advanced toolingcitations
- 2012An international round-robin calibration protocol for nanoindentation measurementscitations
- 20092198 Al–Li plates joined by Friction Stir Welding: Mechanical and microstructural behaviorcitations
- 2009Damping of FeMo alloys obtained from SPS sintering of nanostructured powderscitations
- 2008Effect of thermo-mechanical treatments on the microstructure of micro-alloyed low-carbon steelscitations
- 2006Anelasticity and structural stability of ECAP processed Al-Mg-Si alloys investigated by mechanical spectroscopy
Places of action
Organizations | Location | People |
---|