693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Fromentin, Guillaume
Laboratoire Bourguignon des Matériaux et Procédés
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (33/33 displayed)
- 2021BURR FORMATION AT THE INTERFACE DURING BI-MATERIAL ORTHOGONAL CUTTING
- 2020Multi-physical analysis of the electrochemical behaviour of OFHC copper surfaces obtained by orthogonal cuttingcitations
- 2020Multi-physical analysis of the electrochemical behaviour of OFHC copper surfaces obtained by orthogonal cuttingcitations
- 2020Investigation on PCD cutting edge geometry for Ti6Al4V high-feed millingcitations
- 2020Investigations on Strain Hardening During Cutting of Heat-Resistant Austenitic Stainless Steelcitations
- 2020Investigations on drilling performance of high resistant austenitic stainless steelcitations
- 2019Investigations on exit burr formation mechanisms based on digital image correlation and numerical modellingcitations
- 2019Investigations on exit burr formation mechanisms based on digital image correlation and numerical modellingcitations
- 2019Mechanical analysis of local cutting forces and transient state when drilling of heat-resistant austenitic stainless steelcitations
- 2019CUTTING FORCES IN HIGH FEED MILLING
- 2018On the optimization of the cutting conditions for an improved corrosion resistance of OFHC copper
- 2018On the optimization of the cutting conditions for an improved corrosion resistance of OFHC copper
- 2018Investigation of tool deflection during milling of thread in Cr-Co dental implantcitations
- 2018Investigation of tool deflection during milling of thread in Cr-Co dental implant ; Science Arts & Métiers (SAM)citations
- 2018Fundamental study of exit burr formation mechanisms during orthogonal cutting of AlSi aluminium alloycitations
- 2018Fundamental study of exit burr formation mechanisms during orthogonal cutting of AlSi aluminium alloycitations
- 2018Mechanical study in drilling of heat resistant austenitic stainless steelcitations
- 2017Kinematic Field Measurements During Orthogonal Cutting Tests via DIC with Double-frame Camera and Pulsed Laser Lightingcitations
- 2017Modeling Thread Milling Forces in Mini-hole in Dental Metallic Materialscitations
- 2017A physical-based constitutive model for surface integrity prediction in machining of OFHC coppercitations
- 2017A physical-based constitutive model for surface integrity prediction in machining of OFHC coppercitations
- 2016Flank wear prediction in milling AISI 4140 based on cutting forces PCA for different cutting edge preparationscitations
- 2016Experimental Investigation and Modelling of Burr Formation during Orthogonal Cutting of A356+0.5Cu Aluminium Alloy
- 2016Experimental Investigation and Modelling of Burr Formation during Orthogonal Cutting of A356+0.5Cu Aluminium Alloy
- 2016Analysis and modeling of burr formation during the plane milling of cast aluminium alloy using Polycrystalline Diamond Toolscitations
- 2014Influence of cutting process mechanics on surface integrity and electrochemical behavior of OFHC coppercitations
- 2014Influence of cutting process mechanics on surface integrity and electrochemical behavior of OFHC coppercitations
- 2014Analysis of chip formation mechanisms and modelling of slabber processcitations
- 2013Process Mechanics and Surface Integrity Induced by Dry and Cryogenic Machining of AZ31B-O Magnesium Alloy
- 2013Process Mechanics and Surface Integrity Induced by Dry and Cryogenic Machining of AZ31B-O Magnesium Alloy
- 2013Analytical and experimental investigations on thread milling forces in titanium alloy
- 2008Micro-orthogonal Cutting of Metals
- 2006An Experimental and Analytical Method for Investigating Plastic Flow in Form Tapping
Places of action
| Organizations | Location | People |
|---|