693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Čep, Robert
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (21/21 displayed)
- 2024Electrodeposition of Zn/TiO2 Coatings on Ti6Al4V Produced by Selective Laser Melting, the Characterization and Corrosion Resistance
- 2024Enhancing efficiency in photo chemical machining: a multivariate decision-making approachcitations
- 2024Electrical conductivity analysis of extrusion-based 3D-printed graphenecitations
- 2024Tribological analysis of titanium alloy (Ti-6Al-4V) hybrid metal matrix composite through the use of Taguchi’s method and machine learning classifiers
- 2024An investigation of residual stresses after the turning of high-tempered bearing steelcitations
- 2024Regression model-based parametric analysis of drilling of multi-walled carbon nanotubes-added glass fiber composite laminatescitations
- 2024Tribological investigations of hemp reinforced NAO brake friction polymer composites with varying percentage of resin loadingcitations
- 2024Optimizing end milling parameters for custom 450 stainless steel using ant lion optimization and TOPSIS analysiscitations
- 2024Experimental investigation of tungsten–nickel–iron alloy, W95Ni3.5Fe1.5, compared to copper monolithic bulletscitations
- 2023Microstructure, hardness and wear behavior of ZrC particle reinforced AZ31 surface composites synthesized via friction stir processingcitations
- 2022Experimental Determination of Continuous Cooling Transformation Diagram for High Strength Steel X155CrMoV12 ; Experimentální stanovení transformačního diagramu kontinuálního chlazení pro vysokopevnostní ocel X155CrMoV12
- 2022Dilatometric Analysis of Cooling Curves for High Strength Steel X155CrMoV12 ; Dilatrometrická analýza křivek ochlazování vysokopevnostní oceli X155CrMoV12
- 2022A grey fuzzy approach to the selection of cutting process from the aspect of technological parameterscitations
- 2022Optimizing Friction Stir Welding of Dissimilar Grades of Aluminum Alloy Using WASPAScitations
- 2022Characterization of Microstructural Damage and Failure Mechanisms in C45E Structural Steel under Compressive Loadcitations
- 2019THE INFLUENCE OF CUTTING CONDITIONS ON THE SELECTED PARAMETERS OF THE SURFACE INTEGRITYcitations
- 2015Prediction of the catastrophic tool failure in hard turning through acoustic emission ; Napovedovanje katastrofične poškodbe keramičnih vložkov pri struženju z akustično emisijo
- 2013Influence of cutting parameters on heat-affected zone after laser cutting ; Utjecaj parametara rezanja na zonu utjecaja topline nakon laserskog rezanja
- 2011Cutting tool life tests of ceramic inserts for car engine sleeves ; Ispitivanje trajnosti reznog alata keramičkih uložaka za tuljke automobilskih motora
- 2011Testing of Greenleaf ceramic cutting tools with an interrupted cutting ; Ispitivanje Greenleaf keramičkih reznih alata s prekinutim rezanjem
- 2006Influence and evaluation of selected factors to accoustic sound pressure at abrasive waterjet cutting technology ; Vplyv a hodnotenie vybraných faktorov na hladinu akustického tlaku v technológii delenia vysokorýchlostným hydroabrazívnym prúdom
Places of action
| Organizations | Location | People |
|---|