693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Walsh, Frank
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (14/14 displayed)
- 2020Simulations of fluid flow, mass transport and current distribution in a parallel plate flow cell during nickel electrodepositioncitations
- 2020Electrodeposition of platinum on 3D-printed titanium mesh to produce tailored, high area anodescitations
- 2020Photocatalytic degradation of methylene blue dye on reticulated vitreous carbon decorated with electrophoretically deposited TiO2 nanotubescitations
- 2020Photocatalytic degradation of methylene blue dye on reticulated vitreous carbon decorated with electrophoretically deposited TiO2 nanotubescitations
- 2019Electrodeposition of Ni-P composite coatings: a reviewcitations
- 2018Mass-transfer measurements at porous 3D Pt-Ir/Ti electrodes in a direct borohydride fuel cellcitations
- 2018Decolourisation of reactive black-5 at an RVC substrate decorated with PbO2/ TiO2 nanosheets prepared by anodic electrodepositioncitations
- 2017Titanate nanotubes and nanosheets as a mechanical reinforcement of water-soluble polyamic acid: Experimental and theoretical studies ; Titanate nanosheets (TiNS), titanate nanotubes (TiNT), and scrolled titanate nanosheets (STiNS) were used to synthesise polymer nanocomposites by solution processing. The hardness was found to increase by 90% on addition of 2% TiNS while the modulus (Er) increased by 103% compared to the pure polymer. Small angle X-ray scattering (SAXS) measurements of composite films were used to study alignment of nanostructures within the polymer. The obtained data on mechanical properties of composites have been tested against theoretical values and it was established that both nanostructures alignment as well as their mechanical properties affect the hardness and modulus of the polymer composites. At a low content of TiNS, the reinforcement behaviour matched well with Halpin-Tsai theory which assumes the filler has unidirectional orientation. After addition of 2 wt% TiNT, the hardness and modulus of the polyamic acid salt composites increased by 91% and 165%, respectively, and were higher than theoretical predictions, indicating that both TiNT and STiNS, prepared by hydrothermal synthesis, may have higher mechanical properties than bulk TiO2. At a high filler loading (>2 wt%), the mechanical properties of composites do not fit established theories due to agglomeration of titanate nanostructures.citations
- 2016Titanate nanotubes for reinforcement of a poly(ethylene oxide)/chitosan polymer matrixcitations
- 2016Titanate nanotubes for reinforcement of a poly(ethylene oxide)/chitosan polymer matrixcitations
- 2016Data for the paper: The importance of the film structure during self-powered ibuprofen salicylate drug release from polypyrrole electrodeposited on AZ31 Mg
- 2016The importance of the film structure during self-powered Ibuprofen salicylate drug release from polypyrrole electrodeposited on AZ31 Mgcitations
- 2016The importance of the film structure during self-powered Ibuprofen salicylate drug release from polypyrrole electrodeposited on AZ31 Mgcitations
- 2014The fabrication of a bifunctional oxygen electrode without carbon components for alkaline secondary batteriescitations
Places of action
| Organizations | Location | People |
|---|