693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Noster, Ulf
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (20/20 displayed)
- 2024Effect of Carbon Content on the Phase Composition, Microstructure and Mechanical Properties of the TiC Layer Formed in Hot-Pressed Titanium-Steel Compositescitations
- 2024Preparation methodology for the microstructural characterization of diffusion layers in a titanium/steel composite
- 2023Influence of carbon content on the formation of TiC at diffusion bonded titanium-steel interface
- 2023Quasi-in-Situ Analysis of Electropolished Additively Manufactured Stainless Steel Surfaces
- 2023Enhancement of laser cut edge quality of ultra-thin titanium grade 2 sheets by applying in-process approach using modulated Yb:YAG continuous wave fibre laser
- 2022On the nanoindentation behavior of a TiC layer formed through thermo-reactive diffusion during hot pressing of Ti and cast ironcitations
- 2021An Integrative Experimental Approach to Design Optimization and Removal Strategies of Supporting Structures Used during L-PBF of SS316L Aortic Stentscitations
- 2020Computational analysis of the effects of geometric irregularities and post-processing steps on the mechanical behavior of additively manufactured 316L stainless steel stentscitations
- 2020Mechanical properties of small structures built by selective laser melting 316 L stainless steel – a phenomenological approach to improve component designcitations
- 2008Flame sprayed Al-12Si coatings for the improvement of the adhesion of composite casting profilescitations
- 2008Finite element based optimization of a novel metal-composite-joint
- 2008Effect of Deep Rolling on the Cyclic Performance of Magnesium and Aluminium Alloys in the Temperature Range 20-250°C
- 2007The InnMag project - Processing Mg for civil aircraft applicationcitations
- 2006Mechanical Behavior and Residual Stresses in AZ31 Wrought Magnesium Alloy Subjected to Four Point Bendingcitations
- 2005Residual stress relaxation and cyclic deformation behavior of deep rolled AlMg4.5Mn (AA5083) at elevated temperaturescitations
- 2003On the influence of mechanical surface treatments—deep rolling and laser shock peening—on the fatigue behavior of Ti–6Al–4V at ambient and elevated temperaturescitations
- 2003Isothermal Fatigue Behavior and Residual Stress States of Mechanically Surface Treated Ti-6Al-4V: Laser Shock Peening vs. Deep Rollingcitations
- 2003High Temperature Fatigue of Mechanically Surface Treated Materialscitations
- 2003On the fatigue behavior and associated effect of residual stresses in deep rolled and laser shock peened Ti-6Al-4V at ambient and elevated temperatures
- 2003Verhalten laserschockverfestigter und festgewalzter Randschichten der Ti‐Legierung Ti‐6Al‐4V bei schwingender Beanspruchung unter erhöhten Temperaturencitations
Places of action
| Organizations | Location | People |
|---|