693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Oechsner, Matthias
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (23/23 displayed)
- 2024Requirement-specific Adjustment ofResidual Stresses During Cold Extrusion
- 2024Investigation on surface characteristics of wall structures out of stainless steel 316L manufactured by laser powder bed fusioncitations
- 2024Empowering PVD for corrosion protectioncitations
- 2024Einfluss von Plastifizierung und Abkühlrate auf die Korrosionsbeständigkeit beim artgleichen Rührreibschweißen von EN AW-7020 und EN AW-7075 – Teil 1
- 2024Mechanistic insights into chemical corrosion of AA1050 in ethanol‐blended fuels with water contamination via phase field modeling
- 2024Mechanical Characterization Potentials of Aluminide Diffusion Coatings on Molybdenum Substrates
- 2024Calibration of the residual stresses with an active die during the ejection phase of cold extrusion
- 2024On the Monotonic and Cyclic Behavior of an Al‐Mg‐Zn‐Cu‐Si Compositionally Complex Alloy
- 2023Comparison of Cast, Wrought, and LPBF Processed IN718 Concerning Crack Growth Threshold and Fatigue Crack Growth Behaviorcitations
- 2023On the Monotonic and Cyclic Behavior of an Al‐Mg‐Zn‐Cu‐Si Compositionally Complex Alloycitations
- 2023Increase in residual lifetime due to low amplitude cycles and dwell times at room temperature: Observations and suspected mechanisms
- 2023Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testingcitations
- 2022Investigation of Material Properties of Wall Structures from Stainless Steel 316L Manufactured by Laser Powder Bed Fusioncitations
- 2022Robust determination of fatigue crack propagation thresholds from crack growth datacitations
- 2022Cooling rate as a process parameter in advanced roll forming to tailor microstructure,mechanical and corrosion properties of EN AW 7075 tubes
- 2021On the Influence of Control Type and Strain Rate on the Lifetime of 50CrMo4
- 2021On the Influence of the Microstructure upon the Fatigue and Corrosion Fatigue Behavior of UNS N07718
- 2021Calibration of the residual stresses with an active die during the ejection phase of cold extrusioncitations
- 2020On the Influence of Control Type and Strain Rate on the Lifetime of 50CrMo4citations
- 2020Application of Damage Mechanics and Polynomial Chaos Expansion for Lifetime Prediction of High-Temperature Components Under Creep-Fatigue Loadingcitations
- 2020Effect of Friction Stir Processing on Microstructural, Mechanical, and Corrosion Properties of Al-Si12 Additive Manufactured Componentscitations
- 2018Additive Manufacturing of Glass Components - Exploring the Potential of Glass Connections by Fused Deposition Modelingcitations
- 2014Influence of load signal form and variable amplitude loading on the corrosion fatigue behaviour of aluminium alloyscitations
Places of action
| Organizations | Location | People |
|---|