693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Gao, Nong
University of Southampton
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (38/38 displayed)
- 2024Enhanced mechanical properties and microstructural stability of ultrafine-grained biodegradable Zn-Li-Mn-Mg-Cu alloys produced by rapid solifictaion and high-pressure torsioncitations
- 2024Enhanced mechanical properties and microstructural stability of ultrafine-grained biodegradable Zn–Li–Mn–Mg–Cu alloys produced by rapid solidification and high-pressure torsioncitations
- 2024Interfacial characteristics of multi-material SS316L/IN718 fabricated by laser powder bed fusion and processed by high-pressure torsion
- 2023High densification level and hardness values of additively manufactured 316L stainless steel fabricated by fused filament fabricationcitations
- 2023High densification level and hardness values of additively manufactured 316L stainless steel fabricated by fused filament fabricationcitations
- 2022Effect of heat treatment on fatigue crack growth in IN718/316L multiple-materials layered structures fabricated by laser powder bed fusioncitations
- 2022Effect of heat treatment on fatigue crack growth in IN718/316L multiple-materials layered structures fabricated by laser powder bed fusioncitations
- 2021Fatigue crack growth in IN718/316L multi-materials layered structures fabricated by laser powder bed fusioncitations
- 2021Abnormal grain growth in a Zn-0.8Ag alloy after processing by high-pressure torsioncitations
- 2021Data rich imaging approaches assessing fatigue crack initiation and early propagation in a DS superalloy at room temperaturecitations
- 2020Microstructure and mechanical properties of a Zn-0.5Cu alloy processed by high-pressure torsioncitations
- 2020Effect of sample orientation on the microstructure and microhardness of additively manufactured AlSi10Mg processed by high-pressure torsioncitations
- 2020Effect of sample orientation on the microstructure and microhardness of additively manufactured AlSi10Mg processed by high-pressure torsioncitations
- 2020Comparison between virgin and recycled 316L SS and AlSi10Mg powders used for laser powder bed fusion additive manufacturingcitations
- 2020Comparison between virgin and recycled 316L SS and AlSi10Mg powders used for laser powder bed fusion additive manufacturingcitations
- 2019On the mechanism of oxidation-fatigue damage at intermediate temperatures in a single crystal Ni-based superalloycitations
- 2016Effects of oxidation on fatigue crack initiation and propafation in an advanced disk alloy
- 2016An investigation into the effect of substrate on the load-bearing capacity of thin hard coatingscitations
- 2015Influence of oxidation on fatigue crack initiation and propagation in turbine disc alloy N18citations
- 2014Grain size effects in a Ni-based turbine disc alloy in the time and cycle dependent crack growth regimescitations
- 2013Comparison of fatigue crack propagation behaviour in two gas turbine disc alloys under creep–fatigue conditions: evaluating microstructure, environment and temperature effectscitations
- 2012Characterization of high pressure torsion processed 7150 Al-Zn-Mg-Cu alloycitations
- 2011Hardness homogeneity on longitudinal and transverse sections of an aluminum alloy processed by ECAPcitations
- 2011Influence of strain rate on the characteristics of a magnesium alloy processed by high-pressure torsioncitations
- 2010The evolution of homogeneity during processing aluminium alloys by HPTcitations
- 2010Fabrication of MEMS components using ultra fine grained aluminiumcitations
- 2007Effects of graphite nodules on crack growth behaviour of austempered ductile ironcitations
- 2007Influence of grain structure and slip planarity on fatigue crack growth in low alloying artificially aged 2xxx aluminium alloyscitations
- 2006In situ analysis of cracks in structural materials using synchrotron X-ray tomography and diffractioncitations
- 2006Relations between microstructure, precipitation, age-formability and damage tolerance of Al-Cu-Mg-Li (Mn,Zr,Sc) alloys for age formingcitations
- 2005Room temperature precipitation in quenched Al-Cu-Mg alloys: a model for the reaction kinetics and yield strength developmentcitations
- 2005Microstructure and precipitation in Al-Li-Cu-Mg-(Mn, Zr) alloyscitations
- 2005Microstructural evolution in a spray-cast aluminum alloy during equal-channel angular pressingcitations
- 2004Microstructural developments in a spray-cast Al-7034 alloy processed by equal-channel angular pressing
- 2004Development of Al-Cu-Mg-Li (Mn,Zr,Sc) alloys for age-forming
- 2002Precipitation in stretched Al-Cu-Mg alloys with reduced alloying content studied by DSC, TEM and atom probe
- 2002Development of new damage tolerant alloys for age-forming
- 2000Fatigue-life predictions including the effects of hold time and multiaxial loads on crack-coalescence behaviourcitations
Places of action
| Organizations | Location | People |
|---|