693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Gibmeier, Jens
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (26/26 displayed)
- 2024Analysis of Phase-Specific Strain Pole Figures for Duplex Steels under Elasto-Plastic Uniaxial Tension—Experiment vs. EPSC Modellingcitations
- 2024On the interpretation of Varestraint and Transvarestraint hot cracking test results
- 2024Dynamic evolution of internal stress, grain growth, and crystallographic texture in arc-evaporated AlTiN thin films using in-situ synchrotron x-ray diffractioncitations
- 2024Residual stress engineering for wire drawing of austenitic stainless steel X5CrNi18-10 by variation of die geometries - Effect of drawing speed and process temperaturecitations
- 2023On the Oscillating Course of d$^{hkl}$−sin$^2psi$ Plots for Plastically Deformed, Cold-Rolled Ferritic and Duplex Stainless Steel Sheetscitations
- 2023Kinetics of Martensite Decomposition and Microstructure Stability of Ti-6246 during Rapid Heating to Service Temperaturescitations
- 2023In-situ real-time evolution of intrinsic stresses and microstructure during growth of cathodic arc deposited (Al,Ti)N coatings
- 2023On the Oscillating Course of d$^{hkl}$−sin$^{2}$ψ Plots for Plastically Deformed, Cold-Rolled Ferritic and Duplex Stainless Steel Sheets
- 2022Review on study of internal load transfer in metal matrix composites using diffraction techniquescitations
- 2022Influence of FeCl$_{3}$ and H$_{2}$O$_{2}$ in corrosion testing of modular taper connections in total hip arthroplasty: An in vitro studycitations
- 2021In-Situ Synchrotron X-ray Diffraction Investigation of Microstructural Evolutions During Low-Pressure Carburizingcitations
- 2021Influence of Shot Peening on the Isothermal Fatigue Behavior of the Gamma Titanium Aluminide Ti-48Al-2Cr-2Nb at 750 °Ccitations
- 2021Residual stresses in deep-drawn cups made of duplex stainless steel X2CrNiN23-4citations
- 2021Residual stresses in deep-drawn cups made of duplex stainless steel X2CrNiN23-4 – Influence of the drawing depth
- 2021Investigation of the Effects of Low‐Pressure Carburizing Process Parameters on Microstructural Evolution by Means of In Situ Synchrotron X‐Ray Diffractioncitations
- 2021Investigations on Residual Stresses within Hot-Bulk-Formed Components Using Process Simulation and the Contour Method
- 2020Phase-Specific Strain Hardening and Load Partitioning of Cold Rolled Duplex Stainless Steel X2CrNiN23-4
- 2020Determination of Temperature-Dependent Elastic Constants of Steel AISI 4140 by Use of In Situ X-ray Dilatometry Experimentscitations
- 201920 Hz synchrotron X-ray diffraction analysis in laser-pulsed WC-Co hard metal reveals oscillatory stresses and reversible composite plastificationcitations
- 2019Phase-specific residual stresses induced by deep drawing of lean duplex steel: measurement vs. simulationcitations
- 2018Experimental and numerical analyses of residual stresses induced by tube drawingcitations
- 2018In-Situ Synchrotron X-Ray Diffraction Studies in the Chip Formation Zone During Orthogonal Metal Cuttingcitations
- 2018Application of magnetic Barkhausen noise for residual stress analysis – Consideration of the microstructure = Anwendung des magnetischen Barkhausenrauschens für die Eigenspannungsanalyse – Berücksichtigung der Mikrostrukturcitations
- 2017Spatially resolved temporal stress evolution during laser surface spot hardening of steelcitations
- 2015Fatigue Performance of Medical Ti6Al4V Alloy after Mechanical Surface Treatments
- 2013Effect of built-up edges and transfer layers on the wear state during dry cutting of steel with cemented carbide tools
Places of action
| Organizations | Location | People |
|---|