693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Gubeljak, Nenad
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (36/36 displayed)
- 2024Experimental Characterization and Phase-Field Damage Modeling of Ductile Fracture in AISI 316L
- 2024Numerical Simulation of Fatigue Crack Growth and Fracture in Welded Joints Using XFEM—A Review of Case Studiescitations
- 2024A Study on the Compressive Behavior of Additively Manufactured AlSi10Mg Lattice Structurescitations
- 2024SURFACE ROUGHNESS OF Ti6Al4V ALLOY PRODUCED BY LASER POWDER BED FUSIONcitations
- 2023Mechanical performance of hybrid joints of aluminum sheets and laminated beech veneer plates: an experimental prestudycitations
- 2023Rolling Bearing Fault Detection in the Range of Ultrasound
- 2023Microstructure, hardness and fracture resistance of P235TR1 seam steel pipes of different diameters ; Otpornost prema lomu, tvrdoća i mikrostruktura šavnih cevi različitog prečnika izrađenih od čelika P235TR1
- 2023Load-bearing capacity of hybrid riv-bonded aluminum-magnesium joints at quasi-static and cyclic loadingscitations
- 2023Microstructure, hardness and fracture resistance of P235TR1 seam steel pipes of different diameters
- 2023Mechanical performance and failure behavior of screw-bonded joints of aluminum sheets and cross-laminated birch veneer platescitations
- 2023ASSESSMENT OF FATIGUE BEHAVIOUR OF UHSS STEEL BUTT-WELDED JOINTS BY MEANS OF A FRACTURE MECHANICS METHODOLOGY
- 2022Failure assessment of steel pipes using non-standard ring specimens.
- 2022Effects of fixture configurations and weld strength mismatch on J-integral calculation procedure for SE(B) specimenscitations
- 2022Effects of fixture configurations and weld strength mismatch on J-integral calculation procedure for SE(B) specimenscitations
- 2022Effect of welding processes on the fatigue behaviour of ultra-high strength steel butt-welded jointscitations
- 2022Mechanical characterization of surface modified Ti-based alloy before and after severe plastic deformation
- 2022Influence of the Sheet Edge Condition on the Fracture Behavior of Riv-Bonded Aluminum-Magnesium Jointscitations
- 2020Experimental and numerical analysis of tensile properties of Ti-13Nb-13Zr alloy and determination of influence of anodization processcitations
- 2019Crack tip constraint analysis in welded joints with pronounced strength and toughness heterogeneitycitations
- 2018Numerical simulation of fracture in Ti-6Al-4V alloy for orthopedic applications
- 2018Influence of static strength on the fatigue resistance of weldscitations
- 2017Fracture toughness of a high-strength low-alloy steel weldment ; Žilavost loma zvara visokotrdnega malolegiranega jekla
- 2017Experimental determination of fatigue parameters of high chromium steel under different loading and temperature conditions ; Eksperimentalno određivanje parametara zamornog ponašanja visokokromnog lijevanog čelika pri različitim režimima opterećivanja i temperature
- 2016Characterization of heterogeneous arc welds through miniature tensile testing and Vickers hardness mappingcitations
- 2015Measurement of strain caused by residual stresses in a welded joint using neutron diffraction ; Meritev deformacij povzročenih z zaostalimi napetostmi v zvarnem spoju na osnovi nevtronovskega odklona
- 2015Determination of calibration function for fatigue crack propagation by measurment[!] surface deformation
- 2015The effect of a material's heterogeneity on the stress and strain distribution in the vicinity of a crack front ; Vpliv heterogenosti materiala na porazdelitev napetosti in deformacije v bližini razpoke
- 2015Fracture behaviour of thin sheet stainless steel
- 2012Determination of lower bound fracture toughness of a high strength low alloy steel welded joint
- 2012Tensile test models for low-carbon microalloyed steels with high niobium contents ; Modeli za ispitivanje rastezne čvrstoće nisko-ugljičnih mikrolegiranih čelika s visokim sadržajem niobija
- 2012Effect of residual stresses on the fatigue crack propagation in welded joints
- 2012Assessment of the load-bearing capacity of a primary pipeline
- 2012On the local variation of the crack driving force in a double mismatched weld
- 2012Micromechanical analysis of constraint effect on fracture initiation in strength mis-matched welded joints
- 2012The fracture behaviour of global/local mis-matched weld joints provided on HSLA steels ; Pojav loma v globalno/lokalno trdnostno neenakih zvarnih spojih, izvedenih na visokotrdnostnih jeklih
- 2010HIPERC: a novel, high performance, economic steel concept for linepipe and general structural use
Places of action
| Organizations | Location | People |
|---|