People | Locations | Statistics |
---|---|---|
Naji, M. |
| |
Motta, Antonella |
| |
Aletan, Dirar |
| |
Mohamed, Tarek |
| |
Ertürk, Emre |
| |
Taccardi, Nicola |
| |
Kononenko, Denys |
| |
Petrov, R. H. | Madrid |
|
Alshaaer, Mazen | Brussels |
|
Bih, L. |
| |
Casati, R. |
| |
Muller, Hermance |
| |
Kočí, Jan | Prague |
|
Šuljagić, Marija |
| |
Kalteremidou, Kalliopi-Artemi | Brussels |
|
Azam, Siraj |
| |
Ospanova, Alyiya |
| |
Blanpain, Bart |
| |
Ali, M. A. |
| |
Popa, V. |
| |
Rančić, M. |
| |
Ollier, Nadège |
| |
Azevedo, Nuno Monteiro |
| |
Landes, Michael |
| |
Rignanese, Gian-Marco |
|
Peters, Gwm Gerrit
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (39/39 displayed)
- 2022An experimentally validated model for quiescent multiphase primary and secondary crystallization phenomena in PP with low content of ethylene comonomercitations
- 2020Effect of shear rate and pressure on the crystallization of PP nanocomposites and PP/PET polymer blend nanocomposites
- 2020A filament stretching rheometer for in situ X-ray experimentscitations
- 2019Influence of post-condensation on the crystallization kinetics of PA12:from virgin to reused powder
- 2019Modelling flow induced crystallization of IPPcitations
- 2019In Situ WAXD and SAXS during tensile deformation of moulded and sintered polyamide 12citations
- 2019Influence of post-condensation on the crystallization kinetics of PA12citations
- 2018Structure-properties relations for polyamide 6, part 2citations
- 2018Thin film mechanical characterization of UV-curing acrylate systemscitations
- 2018Thin film mechanical characterization of UV-curing acrylate systems
- 2018Structure-properties relations for polyamide 6, part 2:Influence of processing conditions during injection moulding on deformation and failure kineticscitations
- 2017Glass transition temperature versus structure of polyamide 6:A flash-DSC studycitations
- 2017Glass transition temperature versus structure of polyamide 6citations
- 2017Deformation and failure kinetics of iPP polymorphscitations
- 2016The prediction of mechanical performance of isotactic polypropylene on the basis of processing conditionscitations
- 2015Flow-induced solidification of high-impact polypropylene copolymer compositions : morphological and mechanical effectscitations
- 2015Flow-induced solidification of high-impact polypropylene copolymer compositions : morphological and mechanical effects
- 2013Anisotropic yielding of injection molded polyethylene: experiments and modelingcitations
- 2012Quantification of non-isothermal, multi-phase crystallization of isotactic polypropylene : the influence of shear and pressurecitations
- 2012Quantification of non-isothermal, multi-phase crystallization of isotactic polypropylene : the influence of shear and pressure
- 2012Rate-, temperature-, and structure-dependent yield kinetics of isotactic polypropylenecitations
- 2012Quantification of non-isothermal, multi-phase crystallization of isotactic polypropylene: the influence of cooling rate and pressure
- 2011Linear shear response of the upper skin layerscitations
- 2010Micromechanical modeling of the elastic properties of semicrystalline polymers: a three-phase approachcitations
- 2010Residual stresses in gas-assisted injection moldingcitations
- 2010Molar mass and molecular weight determination of UHMWPE synthesized using a living homogenous catalystcitations
- 2009A novel dilatometer for PVT measurements of polymers at high cooling - and shear ratescitations
- 2009Volumetric rheology of polymers: The influence of shear flow, cooling rate and pressure on the specific volume of iPP and P/E random copolymerscitations
- 2009Model development and validation of crystallization behavior in injection molding prototype flowscitations
- 2008Transient interfacial tension of partially miscible polymerscitations
- 2008Suspension-based rheological modeling of crystallizing polymer meltscitations
- 2008Flow induced crystallization in iPP-DMDBS blends: implications on morphology of shear and phase separationcitations
- 2008Thermoreversible DMDBS Phase Separation in iPP: The Effects of Flow on the Morphologycitations
- 2006Influence of interfacial tension on the morphology of polymer blends
- 2005The influence of cooling rate on the specific volume of isotactic poly(propylene) at elevated pressures
- 2004Structure, deformation, and failure of flow-oriented semicrystalline polymerscitations
- 2004Structure, deformation, and failure of flow-oriented semicrystalline polymers
- 2002The matching of experimental polymer processing flows to viscoelastic numerical simulation
- 2001A 3-D finite element model for gas-assisted injection molding - simulations and experiments
Places of action
Organizations | Location | People |
---|