693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Yasa, Evren
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (24/24 displayed)
- 2024Understanding process parameter-induced variability for tailoring precipitation behavior, grain structure, and mechanical properties of Al-Mg-Si-Mn alloy during solid-state additive manufacturingcitations
- 2024Cleaning and coating procedures determine biological properties of gyroid porous titanium implants
- 2024Systematic review on additive friction stir deposition: materials, processes, monitoring and modellingcitations
- 2024Choosing between commercially pure titanium and Ti-6Al-4V gyroid structures for orthopedic applications:an analysis through Timoshenko beam theory, the Gibson-Ashby model and experimental methodscitations
- 2024Characterisation of materials properties and defects in structure fabricated via additive friction stir deposition
- 2024Choosing between commercially pure titanium and Ti-6Al-4V gyroid structures for orthopedic applicationscitations
- 2023Thin-Walled Commercially Pure Titanium Structures: Laser Powder Bed Fusion Process Parameter Optimizationcitations
- 2021The Laser Powder Bed Fusion Process Development of 17-4 PH Stainless Steels with Pulsed-Wave Lasers
- 2021Parametric simulations for residual stresses and distortions of inconel 625 fabricated by laser powder bed fusion additive manufacturing
- 2019Dimensional Accuracy and Mechanical Properties of Chopped Carbon Reinforced Polymers Produced by Material Extrusion Additive Manufacturingcitations
- 2018Additive Manufacturing of Polymer Matrix Compositescitations
- 2012Investigation on the inclusions in maraging steel produced by selective laser melting
- 2012Assessing and comparing influencing factors of residual stresses in selective laser melting using a novel analysis methodcitations
- 2012A preliminary investigation on selective laser melting of M2 high speed steel
- 2011The investigation of the influence of laser re-melting on density, surface quality and microstructure of selective laser melting parts
- 2010Microstructure and mechanical properties of maraging steel 300 after Selective Laser Melting
- 2010Part and material properties in selective laser melting of metals
- 2009Microstructure evolution of selective laser molten 316L stainless steel parts with laser re-melting
- 2009Improving Productivity Rate in SLM of Commercial Steel Powders
- 2009Experimental investigation of laser surface re-melting for the improvement of selective laser melting process
- 2009Investigation on occurrence of elevated edges in Selective Laser Melting
- 2009Rapid Manufacturing Research at the Catholic University of Leuven
- 2009An Experimental study of Process Parameters in Laser Marking
- 2009Experimental Investigation of Charpy Impact Tests on Metallic SLM parts
Places of action
| Organizations | Location | People |
|---|