| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Arsić, Dušan
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (19/19 displayed)
- 2024Advanced welding technologies: FSW in automotive manufacturing
- 2024Influence of FDM printing parameters on the compressive mechanical properties and fracture behavior of ABS material
- 2024A new artificial neural network model for predicting fatigue limit and fracture toughness values of some stainless steels
- 2024A new artificial neural network model for predicting fatigue limit and fracture toughness values of some stainless steels
- 2024Assessment of mechanical properties of austenitic stainless steels using artificial neural networks
- 2024Predicting the yield stress and tensile strength of two stainless steel using artificial intelligence
- 2023Prediction of service life of components and structures of hydro power plants during the design, prototyping and service period
- 2023Influence of TiN Coating on the Drawing Force and Friction Coefficient in the Deep Drawing Process of AlMg4.5Mn0.7 Thin Sheetscitations
- 2023Effect of plastic strain and specimen geometry on plastic strain ratio values for various materialscitations
- 2022Theoretical-experimental estimation of weldability of different types of steels by hard facing
- 2022Analysis of Filler Metals Influence on Quality of Hard-Faced Surfaces of Gears Based on Tests in Experimental and Operating Conditionscitations
- 2021Influence of different hard-facing procedures on quality of surfaces of regenerated gearscitations
- 2020The effect of heat input on the fracture behaviour of surface weld metal of rail steel
- 2018Tribological characteristics of Al/SiC/Gr hybrid compositescitations
- 2018The influence of heat input on the toughness and fracture mechanism of surface weld metal
- 2018Working life estimate of the tubular T-joint by application of the LEFM concept
- 2018Experimental-numerical analysis of appearance and growth of a crack in hard-faced layers of the hot-work high-strength tool steels
- 2016COMPARATIVE STUDY OF AN ENVIRONMENTALLY FRIENDLY LUBRICANT WITH CONVENTIONAL LUBRICANTS IN STRIP IRONING TEST
- 2015Two-phase ironing process in conditions of ecologic and classic lubricants application
Places of action
| Organizations | Location | People |
|---|
article
COMPARATIVE STUDY OF AN ENVIRONMENTALLY FRIENDLY LUBRICANT WITH CONVENTIONAL LUBRICANTS IN STRIP IRONING TEST
Abstract
Experimental estimates of ecologically acceptable single-bath lubricant, are presented and compared to those of classical lubricants in this paper. A device was created for the realisation of the strip ironing test with double thinning and a appropriate definition of the friction coefficient is used. Strips of 2.5 mm-thick low carbon steel sheets were used in the single-phase process with a maximum thinning deformation of 25%. In addition to the single-bath ecological lubricant, a phosphate layer with mineral oil was applied, as was lithium lubricating grease with MoS2 and mineral oil with EP additives. The basic criterion for the estimates was the change in the friction coefficient and the secondary criterion was the level of surface microchanges due to sliding. The applied test procedure enables the clear differences between the lubricating properties of the investigated lubricants to be established. ; The work reported in this paper was partially financially supported by the Serbian Ministry of Education and Science, through contracts TR 34002, TR 35024, and TR 32036 ; Published