| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Zouhar, Jan
Brno University of Technology
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (13/13 displayed)
- 2024Study of dynamic behaviour via Taylor anvil test and structure observation of M300 maraging steel fabricated by the selective laser melting methodcitations
- 2024Machinability of extruded H13 tool steel: Effect of cutting parameters on cutting forces, surface roughness, microstructure, and residual stressescitations
- 2024Effect of high-speed steel screw drill geometry on cutting performance when machining austenitic stainless steelcitations
- 2023Analysis of Ballistic Impact of 7.62 mm FMJ M80 Rifle Projectile into Twaron/UHMWPE Composite Armorcitations
- 2023Influence of Aging Temperature on Mechanical Properties and Structure of M300 Maraging Steel Produced by Selective Laser Meltingcitations
- 2022Evaluation of ballistic resistance of thermoplastic and thermoset composite panelscitations
- 2022Cutting Force When Machining Hardened Steel and the Surface Roughness Achievedcitations
- 2022Application of Carbon–Flax Hybrid Composite in High Performance Electric Personal Watercraftcitations
- 2021Mechanical Properties of Flax and Hybrid Composite Materals
- 2021Design and validation of motorcycle single side swingarm made of CFRP using photogrammetry
- 2021APPLICATION OF FLAX HYBRID COMPOSITE ON THE HIGH PERFORMANCE ELECTRIC PERSONAL WATERCRAFT
- 2020Design and stiffness Distribution analysis of motorcycle swingarm made of carbon fiber composites
- 2010On the Application of the PVD Hard Coatings for Ball Milling of Shaped Surfaces
Places of action
| Organizations | Location | People |
|---|
article
Study of dynamic behaviour via Taylor anvil test and structure observation of M300 maraging steel fabricated by the selective laser melting method
Abstract
This paper deals with the M300 high strength maraging steel fabricated via selective laser melting method. Mechanical properties especially microhardness and compressive yield strength of maraging steel in as-printed state were observed. The acquired data was implemented in Johnson-Cook constitutive equation used for numeric simulation, which showed the satisfactory correlation with the observed experiment. Dynamic behaviour under high strain rate (impact velocity reached 185 m.s-1)- 1 ) was investigated via Taylor Anvil Test. The experiment revealed structure and geometrical changes accompanied with the creation of characteristic funnellike and cylindrical areas on the deformed sample. Impacted sample forehead featured the increase of micro- hardness (465 HV) accompanied with structure changes. The structure in the funnel-like area exhibited the decrease of average grain size, which reached the minimum (3.1 mu m) in the vicinity of the impacted forehead. Closer analysis revealed that the high strain rate caused the increase of high fraction high-angle grain boundaries (50,8 %) and higher geometrically necessary dislocation density (52.77 1.m-- 2 ) in the funnel-like area.