| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Wiśniewski, Paweł
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (26/26 displayed)
- 2021Influence of an aluminizing process on the microstructure and tensile strength of the nickel superalloy IN 718 produced by the Selective Laser Meltingcitations
- 2020Investigation of the Properties of S i C based Ceramic Slurries and Shell Moulds Cooling using Thermal Imaging Camera
- 2020Molding Binder Influence on the Porosity and Gas Permeability of Ceramic Casting Moldscitations
- 2020Analysis of Microstructure and Properties of a Ti–AlN Composite Produced by Selective Laser Meltingcitations
- 2020Microstructure and Mechanical Properties of Austenitic 316L Steel Samples Obtained by Selective Laser Melting
- 2018Determination of loamy resources impact on granulation of ceramic proppants and their propertiescitations
- 2017Assesment of Infrared Drying Time of Ceramic Shell Molds with use of Thermal Imaging Camera
- 2017Evaluation of Cooling Time of SiC Ceramic Mold Using Thermal Imaging Camera
- 2017Detection of the Surface Structure Defects in Ceramic Shell Molds Using a Thermovisual Camera
- 2017Effect of adding water-based binders on the technological properties of ceramic slurries based on silicon carbide citations
- 2017Microstructure characterization of ceramic shell molds
- 2017Manufacture of Ceramic Shell molds; Monitoring the Processes with the Use of a Thermo-visual Camera
- 2017Influence of Duplex Surface Treatment on the High-Cycle Fatigue Resistance of the IN 713C Nickel Superalloy
- 2016Investigation of the Basic Properties of Ceramic Proppants in Raw State Obtained by the Method of Mechanical Granulationcitations
- 2016Selecting key parameters of the green pellets and lightweight ceramic proppants for enhanced shale gas exploitationcitations
- 2016Investigation of key parameters influence on properties of the green pellets and lightweight ceramic proppants obtained by mechanical granulation method citations
- 2016Characterization and evaluation properties of ceramic proppants used in the extraction of the unconventional hydrocarbons
- 2016Rheological properties of alumina ceramic slurries for ceramic shell-mould fabricationcitations
- 2016Optimizing the Lightweight Ceramic Proppants Propertiescitations
- 2016Technological Properties of Ceramic Slurries Based on Silicon Carbide with Poly(vinyl alcohol) Addition for Shell Moluds Fabrication in Precision Casting Processcitations
- 2016Experimental ceramic proppants characterization in the process of shale gas extraction
- 2015Studies of the properties of green ceramic proppants obtained by spray drying method
- 2015Study of deflocculation of white clay for obtaining ceramic proppants fabrication in spray dryer
- 2015Influence of deflocculant addition on rheological properties of the slurries based on bauxite
- 2004Effect of glass transition temperature of polymeric binders on properties ceramic materialscitations
- 2001Vinyl Acetate Copolymers in Die Pressing of Aluminacitations
Places of action
| Organizations | Location | People |
|---|
article
Investigation of the Properties of S i C based Ceramic Slurries and Shell Moulds Cooling using Thermal Imaging Camera
Abstract
Silicon Carbide is a very pr o spective material in modern precision casting. SiC ischaracterized by a higher thermal conductivity than the commonly used powders , i.e. Al 2 O 3 ,aluminosilicates and ZrO 2 Also a n interesting aspect is the application of a binder containingfibers, which increase s the gas permeability of ceramic shell mo u lds. The paper presents the resultsof a research of casting materials in the delivery state. The article discusses the results ofinvestigations performed on a power and a binder in the delivery state as well as the properties ofmoulding sands. The main component of the ceramic mixtures was silicon carbide with the meanparticle size of 21.8 μ m. The morphologies of the pow d er and the binder were exa m ined o n a ligh tmicro s cope as well as a scanning microscope ( The obtained casting slip assigned for the firstlayer of the mould had the vi s cosity in the scope of 29 21 s , and that for the constru ction layers inthe range of 17 12 s. The e valuation of t he properties of the samples concerned the cooling of theSiC specimen , which w as investigated with the use of a therm al imaging camera. It has been shownthat the use of temperature field measurements with a therm ovision camera is an interestingsolution for the evaluati o n of the cooling processes of ceramic shell mo u lds.