| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Van Erps, Jurgen
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (21/21 displayed)
- 2023VCSEL wavelength tunability using controlled mechanical strain
- 2021Increasing the Microfabrication Performance of Synthetic Hydrogel Precursors through Molecular Designcitations
- 20203D direct laser writing of microstructured optical fiber tapers on single-mode fibers for mode-field conversioncitations
- 2018Ultrathin Poly-DL-Lactic Membranes for Corneal Endothelial Transplantation
- 2018Localized optical- quality doping of graphene on silicon waveguides through a TFSA- containing polymer matrixcitations
- 2016Replication of self-centering optical fiber alignment structures using hot embossingcitations
- 2016Hot-embossing replication of self-centering optical fiber alignment structures prototyped by deep proton writingcitations
- 2016Deep proton writing with 12 MeV protons for rapid prototyping of microstructures in polymethylmethacrylatecitations
- 2016Optofluidic multi-measurement system for the online monitoring of lubricant oilcitations
- 2016Design and prototyping of self-centering optical single-mode fiber alignment structurescitations
- 2015Mould insert fabrication of a single-mode fibre connector alignment structure optimized by justified partial metallizationcitations
- 2013Low-coherence interferometry with polynomial interpolation on Compute Unified Device Architectur-enabled graphics processing units
- 2013Gloss, hydrophobicity and surface texture of papers with organic nanoparticle coatings
- 2013B-Calm: An open-source multi-GPU-based 3D-FDTD with multi-pole dispersion for plasmonics
- 2010Populating multi-fiber fiberoptic connectors using an interferometric measurement of fiber tip position and facet quality
- 2010Design and fabrication of embedded micro-mirror inserts for out-of-plane coupling in PCB-level optical interconnects
- 2008Hot embossing of microoptical components prototyped by deep proton writing
- 2008Embedded Micro-Mirror inserts for optical printed circuit boards
- 2008Deep Proton Writing: A tool for rapid prototyping of polymer micro-opto-mechanical modules
- 2007Deep Proton Writing: A tool for rapid prototyping polymer micro-opto-mechanical modules
- 2006Laser Ablation of Parallel Optical Interconnect Waveguides
Places of action
| Organizations | Location | People |
|---|
article
Laser Ablation of Parallel Optical Interconnect Waveguides
Abstract
Excimer laser ablation is presented as an alternative technology to photolithography for the fabrication of board-level parallel optical interconnect waveguides. Arrays of polymer multimode waveguides with a 50 x 50 mu m(2) cross section on a 125-mu m pitch are fully characterized. Root mean square sidewall roughness is 35 nm; no deposition of debris is observed on scanning electron microscope images. The first conclusion out of loss spectrum measurements is a "yellowing effect" of laser ablated waveguides' leading to an increased loss at shorter wavelengths. The second important conclusion is a potential low loss at a wavelength of 850, 980, and 1310 nm. This is verified at 850 nm by cutback measurements on 10-cm-long waveguides showing an average propagation loss of 0.13 dB/cm.