| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Valente, Emilie Hørdum
Technical University of Denmark
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (18/18 displayed)
- 2023Wire arc additive manufacturing of thin and thick walls made of duplex stainless steelcitations
- 2022Powder-based additive manufacturing of high-nitrogen stainless steels and austenitic nickel alloys
- 2022Powder-based additive manufacturing of high-nitrogen stainless steels and austenitic nickel alloys
- 2021In-situ interstitial alloying during laser powder bed fusion of AISI 316 for superior corrosion resistancecitations
- 2021In-situ interstitial alloying during laser powder bed fusion of AISI 316 for superior corrosion resistancecitations
- 2021Microstructure Optimization of AM metals through heat treatment and interstitial alloying
- 2021Targeted heat treatment of additively manufactured Ti-6Al-4V for controlled formation of Bi-lamellar microstructurescitations
- 2020Gaseous surface hardening of Ti-6Al-4V fabricated by selective laser meltingcitations
- 2019Effect of scanning strategy during selective laser melting on surface topography, porosity, and microstructure of additively manufactured Ti-6Al-4Vcitations
- 2019Effect of scanning strategy during selective laser melting on surface topography, porosity, and microstructure of additively manufactured Ti-6Al-4Vcitations
- 2019Influence of atmosphere on microstructure and nitrogen content in AISI 316L fabricated by laser‐based powder bed fusion
- 2019Influence of atmosphere on microstructure and nitrogen content in AISI 316L fabricated by laser‐based powder bed fusion
- 2019The Effect of Heat Treatment and Surface Hardening of 3D Printed Austenitic Stainless Steel AISI316l on Corrosion and Wear Properties
- 2019The Effect of Heat Treatment and Surface Hardening of 3D Printed Austenitic Stainless Steel AISI316l on Corrosion and Wear Properties
- 2019A method for identification and quantification of thermal lensing in powder bed fusion
- 2019Multi-material additive manufacturing of steels using laser powder bed fusion
- 2018High-temperature solution nitriding and low-temperature surface nitriding of 3D printed stainless steel
- 2018Modelling of the microstructural evolution of Ti6Al4V parts produced by selective laser melting during heat treatment
Places of action
| Organizations | Location | People |
|---|
document
The Effect of Heat Treatment and Surface Hardening of 3D Printed Austenitic Stainless Steel AISI316l on Corrosion and Wear Properties
Abstract
The present work focuses on the effect of heat treatment and surface hardening on the microstructure, wear characteristics and corrosion resistance, of 316L stainless steel produced<br/>by Selective Laser Melting (SLM). Specifically, the high temperature treatments austenitisation, high temperature solution nitriding (HTSN) and a new “active austenitisation” treatment, performed with a controlled low partial pressure of nitrogen, were investigated. Additionally, low temperature surface nitriding (LTSN) was investigated for surface hardening. Gaseous thermochemical treatments are well suited for SLM parts, as uniform hardening is achieved on all surfaces exposed to the reactive gas. The wear resistance was tested in a pin-on-disc setup under dry conditions using an AISI 52100 ball as a counterpart, revealing significantly higher wear resistance after LTSN treatment, due to increased surface hardness, while a significant reduction in wear resistance was observed after HTSN treatment. High temperature treatments resulted in the removal of both melt-pool and cellular structures, resulting in a more homogenous material. This lead to improved corrosion resistance as reflected by a lower current density in the passive region during cyclic potentiodynamic polarization testing (CPP) LTSN treatments lead to dramatically increased pitting potentials and improved repassivation characteristics.