693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Tuck, Christopher
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (25/25 displayed)
- 2023Strategies for Integrating Metal Nanoparticles with Two-Photon Polymerization Process: Toward High Resolution Functional Additive Manufacturingcitations
- 2023Additively Manufactured 3D Micro-bioelectrodes for Enhanced Bioelectrocatalytic Operationcitations
- 2023Strategies for Integrating Metal Nanoparticles with Two-Photon Polymerization Processcitations
- 2022Reactive Jetting of High Viscosity Nanocomposites for Dielectric Elastomer Actuationcitations
- 2022Antimicrobial ‘inks’ for 3D printing: block copolymer-silver nanoparticle composites synthesised using supercritical CO2citations
- 2021The influence of printing parameters on multi-material two-photon polymerisation based micro additive manufacturingcitations
- 2021An imidazolium-based supramolecular gelator enhancing interlayer adhesion in 3D printed dual network hydrogelscitations
- 2021Bespoke 3D-Printed Polydrug Implants Created via Microstructural Control of Oligomerscitations
- 2021Bespoke 3D-Printed Polydrug Implants Created via Microstructural Control of Oligomerscitations
- 2018Compressive failure modes and energy absorption in additively manufactured double gyroid latticescitations
- 2018Selective recrystallization of cellulose composite powders and microstructure creation through 3D binder jettingcitations
- 2018Reactive material jetting of polyimide insulators for complex circuit board designcitations
- 2018Band gap behavior of optimal one-dimensional composite structures with an additive manufactured stiffenercitations
- 2018Author Correction: Additive manufacture of complex 3D Au-containing nanocomposites by simultaneous two-photon polymerisation and photoreduction
- 2018Scanning photocurrent microscopy of 3D printed light trapping structures in dye-sensitized solar cellscitations
- 20173D inkjet printing of electronics using UV conversioncitations
- 2017Additive manufacture of complex 3D Au-containing nanocomposites by simultaneous two-photon polymerisation and photoreductioncitations
- 2017Insights into the mechanical properties of several triplyperiodic minimal surface lattice structures made by polymeradditive manufacturingcitations
- 2016Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using x-ray computed tomographycitations
- 2016Additive manufacture of three dimensional nanocomposite based objects through multiphoton fabricationcitations
- 2016Additive Manufacture of Three Dimensional Nanocomposite Based Objects through Multiphoton Fabricationcitations
- 20163D inkjet-printed UV-curable inks for multi-functional electromagnetic applicationscitations
- 2015Nano-hardness and microstructure of selective laser melted AlSi10Mg scan trackscitations
- 2014On the texture formation of selective laser melted Ti-6Al-4Vcitations
- 2014An experimental study into the effects of bulk and flow behaviour of laser sintering polymer powders on resulting part propertiescitations
Places of action
| Organizations | Location | People |
|---|
article
Additive manufacture of three dimensional nanocomposite based objects through multiphoton fabrication
Abstract
Three dimensional structures prepared from a gold-polymer composite formulation have been fabricated using multiphoton lithography. In this process, gold nanoparticles were simultaneously formed through photoreduction whilst polymerisation of two possible monomers was promoted. The monomers, trimethylopropane triacrylate (TMPTA) and pentaerythritol triacrylate (PETA) were mixed with a gold salt, but it was found that the addition of a Ruthenium (II) complex enhanced both the geometrical uniformity and integrity of the polymerized / reduced material, enabling the first production of 3D gold-polymer structures by single step multiphoton lithography.