| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Gu, Jun
Vrije Universiteit Brussel
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (13/13 displayed)
- 2024Thermal Reactivation of Hydrated Cement Paste: Properties and Impact on Cement Hydrationcitations
- 2024Alkali-Activated Copper Slag with Carbon Reinforcement: Effects of Metakaolinite, OPC and Surfactants
- 2023Influence of the curing conditions on the mechanical properties of alkali-activated copper slag-basalt-based thin composites
- 2023The Influence of the Thermal Treatment of Copper Slag on the Microstructure and Performance of Phosphate Cementscitations
- 2015Calibration and correction procedure for quantitative out-of-plane shearographycitations
- 2012'Gradient' polar scan technique for material characterizationcitations
- 2012Polar scan technique for material characterization and identification of new operating regimes
- 2012Study of the geometrical inaccuracy on a SPIF two-slope pyramid by finite element simulationscitations
- 2010Resonance Fatigue Testing of Test Beams Made of Composite Material
- 2006Stereolithographic Specimen to Calibrate Permeability Measurements for RTM Flow Simulations
- 2001Behaviour of Sandwich Panels with E-glass Fibre Reinforced Cementitious Faces under Repeated Loading
- 2000The use of a new cementitious glass fibre reinforced composite in sandwich structures for building applications
- 2000Evaluation of fatigue and durability properties of E-glass reinforced phosphate cementitious composite
Places of action
| Organizations | Location | People |
|---|
document
Influence of the curing conditions on the mechanical properties of alkali-activated copper slag-basalt-based thin composites
Abstract
In this work, a series of composites fabricated with a matrix based on copper slag-metakaolinite and potassium silicate solution, reinforced with basalt fibers, were cured in different conditions (temperature, pressure, and time) to find the optimal curing parameters. This comparative study presents their influence on the mechanical properties of the laminates/composites produced. Differential scanning calorimetry was used to collect information on the matrix on heating till 250 °C. The use of a hot press for the curing allowed to achieve similar volume fractions and improve matrix impregnation. The flexural strength and elastic modulus were used to evaluate the mechanical performance of the samples. The results showed that 80 °C is a reasonable curing temperature. Curing the samples for 1 h at 80 °C led to flexural strength up to 100 MPa and elastic modulus up to 20 GPa. However, increasing the curing time to 2 or 3 hours was observed to have no significant effect on the optimal strength. Similarly, higher processing pressure was observed not to positively affect the mechanical properties. These results are of interest for the reuse of copper slag in the development of structural thin composites for potential building applications.