| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Michalski, Andrzej
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (13/13 displayed)
- 2019Microstructure and thermoelectric properties of p and n type doped β-FeSi2 fabricated by mechanical alloying and pulse plasma sinteringcitations
- 2018Structure and mechanical properties of TiB 2 /TiC – Ni composites fabricated by pulse plasma sintering methodcitations
- 2017Design of interfacial Cr 3 C 2 carbide layer via optimization of sintering parameters used to fabricate copper/diamond composites for thermal management applicationscitations
- 2011W/steel joint fabrication using the pulse plasma sintering (PPS) methodcitations
- 2010Nanocrystalline WC with non-toxic Fe-Mn bindercitations
- 2010Properties of WCCo/diamond composites produced PPS method intended for drill bits for machining of building stonescitations
- 2008Heat Sink Materials Processing by Pulse Plasma Sinteringcitations
- 2007Nanocrystalline cemented carbides sintered by the pulse plasma methodcitations
- 2006Nanocrystalline Cemented Carbides Sintered by the Pulse Plasma Methodcitations
- 2006Nanocrystalline Cu-Al2O3 Composites Sintered by the Pulse Plasma Techniquecitations
- 2006NiAl–Al2O3 composites produced by pulse plasma sintering with the participation of the SHS reactioncitations
- 2004Phase transformations in ball milled AISI 316L stainless steel powder and the microstructure of the steel obtained by its sintering
- 2002Fabrication, structure and consolidation of NiAl-Al <inf>2</inf> O <inf>3</inf> mechanically alloyed nanocomposite powders
Places of action
| Organizations | Location | People |
|---|
article
Phase transformations in ball milled AISI 316L stainless steel powder and the microstructure of the steel obtained by its sintering
Abstract
<p>The paper shows the influence of the 100 hours ball milling process of commercial AISI 316L stainless steel powder and the mixture of powders of its components eg. (Fe, Cr, Ni...) on the structure on the milling products. The impulse plasma sintering process of the powders has also been carried out. The results of X-ray diffractometry showed that ball milling in both cases leads to obtaining nanocrystalline two phase (austenitic-martensitic) stainless steel powders of the average size of crystallite about 40 nm. The fraction of martensite in the milled powders was estimated from Mössbauer spectra and their microstructure was observed on scanning electron microscope. The milled powders were sintered by impulse plasma sintering. The structure of the sintered material was characterized by X-ray diffractometry and light microscopy. It was found that impulse plasma sintering of nanocrystalline powders obtained by ball milling of pure components enable to obtain a nanocrystalline austenitic stainless steel of very low porosity. © 2004 Advanced Study Center Co. Ltd.</p>