| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Allazadeh, Mohammad Reza
University of Strathclyde
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (18/18 displayed)
- 2023Superplastic forming of 1050 aluminium alloy
- 2020Computing strain rate sensitivity of aluminium alloy 1050
- 2018Studying the effect of hydroxyapatite particles in osteoconductivity of Ti-HA bioceramiccitations
- 2018Analysing the effect of strain rate and temperature on the flow stress in AA1050 sheet using E-2448 standard
- 2018Suggesting a full two level experimental factorial model with three factors to optimize Ti-HA biocomposite properties
- 2017Manufacture of a four-sheet complex component from different titanium alloys by superplastic forming
- 2017Application of superplastic forming in manufacture four-sheet sandwich panel sheetstock
- 2015Formation of defects in the steel microstructure during solidification and their effects on the steel material
- 2015Application of milling in synthesizing nanostructured metal matrix composite powdercitations
- 2013Reinforced aluminum matrix composite application in friction materialcitations
- 2012Cooling rate optimization of as-cast consciously cast steel
- 2012High strain rate compressive tests on woodcitations
- 2011High strain rate compressive tests on woven graphite epoxy compositescitations
- 2011FEM technique to study residual stresses developed in continuously cast steel during solid-solid phase transformationcitations
- 2010Cooling Rate Optimization for Quenching As-Cast Steel in Industry
- 2010Stresses introduced during cooling the as-cast steel slab
- 2009Using Small Specimens Technique in Nuclear Pressure Vessel Survey
- 2009The Effect of Cooling Rate on the Microstructure Configuration of Continuously Cast Steel Slabs
Places of action
| Organizations | Location | People |
|---|
article
Suggesting a full two level experimental factorial model with three factors to optimize Ti-HA biocomposite properties
Abstract
A metal matrix composites (MMCs) is introduced to serve as synthetic bone grafts. The MMC was synthetized via powder metallurgical method after milling raw powder mixture of hydroxyapatite (HA) particles and pure titanium (Ti) powder. A full two level experimental factorial model with three factors (2^3) was developed to study the effect of three main parameters of synthetizing process on the hardness, density, and crystallite size of the composite. The synthetizing process parameters under consideration were the mechanical alloying time as well as the ceramic powder initial size and its mass fraction in the mixed powder. The results demonstrate that the composite’s hardness is increasing with higher HA mass fraction (W/W) of the composite and longer milling time. The analysis of data also show that the initial HA particle size has insignificant influence on the composite’s hardness, while higher HA content fraction in the MMC decreases the density of the composite.