| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Birkett, Martin
Northumbria University
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (23/23 displayed)
- 2024Precision depth-controlled isolated silver nanoparticle-doped diamond-like carbon coatings with enhanced ion release, biocompatibility, and mechanical performancecitations
- 2023Soft diamond-like carbon coatings with superior biocompatibility for medical applicationscitations
- 2023Biocompatible Ti3Au–Ag/Cu thin film coatings with enhanced mechanical and antimicrobial functionalitycitations
- 2023Biocompatible Ti3Au–Ag/Cu thin film coatings with enhanced mechanical and antimicrobial functionalitycitations
- 2022Enhanced mechanical and biocompatibility performance of Ti(1- x )Ag(x) coatings through intermetallic phase modificationcitations
- 2022Thermal activation of Ti(1-x)Au(x) thin films with enhanced hardness and biocompatibility citations
- 2022Tribological Behavior of Microalloyed Cu50Zr50 Alloy
- 2022Tribological Behavior of Microalloyed Cu50Zr50 Alloy
- 2022Mn3Ag(1-x)Cu(x)N antiperovskite thin films with ultra-low temperature coefficient of resistancecitations
- 2022Mn3Ag(1-x)Cu(x)N antiperovskite thin films with ultra-low temperature coefficient of resistancecitations
- 2022Investigating the Thermal and Mechanical Properties of Polyurethane Urea Nanocomposites for Subsea Applications
- 2022Thermal activation of Ti(1-x)Au(x) thin films with enhanced hardness and biocompatibilitycitations
- 2021Mechanical performance of biocompatible Ti-Au thin films grown on glass and Ti6Al4V substrates
- 2021Effect of noble metal (M=Ag, Au) doping concentration on mechanical and biomedical properties of Ti-M matrix thin films co-deposited by magnetron sputtering
- 2019A Numerical and Experimental Study of Adhesively-Bonded Polyethylene Pipelinescitations
- 2018Tuning the antimicrobial behaviour of Cu85Zr15 thin films in “wet” and “dry” conditions through structural modificationscitations
- 2016Mechanical behaviour of adhesively bonded polyethylene tapping teescitations
- 2016Electrical resistivity of CuAlMo thin films grown at room temperature by dc magnetron sputteringcitations
- 2016Resistor trimming geometry; past, present and futurecitations
- 2015Investigation into the Development of an Additive Manufacturing Technique for the Production of Fibre Composite Productscitations
- 2012Optimization of the deposition and annealing of CuAIMo thin film resistors
- 2008Discrete resistor technologies and potential future advancements
- 2006Effects of annealing on the electrical properties of NiCr vs AlCu thin film resistors prepared by DC magnetron sputtering
Places of action
| Organizations | Location | People |
|---|
conferencepaper
Mechanical performance of biocompatible Ti-Au thin films grown on glass and Ti6Al4V substrates
Abstract
Ti-Au intermetallic based material systems are being extensively studied to develop hard and wear resistant biocompatible thin film coatings over implant devices to extend their lifetime [1, 2]. However, the measurement of these mechanical characteristics depends upon factors such as surface properties of the substrates and their temperature during thin film deposition. In this work, Ti-Au thin films were deposited by magnetron sputtering on both glass and Ti6Al4V substrates at two different temperatures. These films were studied for their mechanical properties by the nanoindentation technique in both load control and displacement control modes using a Berkovich tip. XRD patterns and cross section SEM images detail the microstructure while AFM images present the surface morphology of these Ti-Au thin films. Biocompatibility of the films is verified by cytotoxicity tests on L929 mouse fibroblast cells using Alamar blue reagent and the ions leaching in the film extracts is measured using the ICPOEMS technique. Standard deviation for hardness of films on glass substrates is ~4 times lower than that on Ti6Al4V substrates and is corelated to a corresponding increase in surface roughness from 2nm for glass to 40nm for Ti6Al4V substrates [3]. Increasing substrate temperature leads to an increase in film hardness from 5.1 to 8.9GPa and is related to the development of a super hard β phase of the Ti3Au intermetallic. The standard deviation of this peak mechanical hardness value of 8.9GPa is reduced by 3 times when measured in displacement control mode compared to the value measured in load control mode due of the effect of nanoindentation tip penetration depth. All the Ti-Au thin films exhibit excellent cytotoxicity values above 95% and ion leaching below 100ppb. This work presents a comparative study to optimize hardness measurement of Ti-Au thin films, critical for a better understanding of these super hard biocompatible coatings.