| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Shukla, P. P.
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (9/9 displayed)
- 2011Mathematical modelling of the fibre laser surface processing of a zirconia engineering ceramic by means of three-dimensional finite element analysiscitations
- 2011Characterization and compositional study of a ZrO2 engineering ceramic irradiated with a fibre laser beamcitations
- 2011Influence of laser beam brightness during surface treatment of a ZrO2 engineering ceramic
- 2011Distribution of temperature during fibre laser radiation and the effects on the phase transformation of ZrO2 engineering ceramiccitations
- 2011Modification of fracture toughness parameter K1c following CO2 laser surface treatment of Si3N4 engineering ceramiccitations
- 2011Evaluation of fracture toughness of ZrO2 and Si3N4 engineering ceramics following CO2 and fibre laser surface treatmentcitations
- 2011Examination of temperature distribution and the thermal effects on Si3N4 engineering ceramics during fibre laser surface treatmentcitations
- 2010Fracture toughness modification by using a fibre laser surface treatment of a silicon nitride engineering ceramiccitations
- 2010On the establishment of an appropriate method for evaluating the residual stresses after laser surface treatment of ZrO2 and Si3N4 engineering ceramics
Places of action
| Organizations | Location | People |
|---|
article
Influence of laser beam brightness during surface treatment of a ZrO2 engineering ceramic
Abstract
A comparative study between fibre and Nd:YAG (neodymium, yttrium, aluminium, garnet) laser surface treatment on a cold isostatic pressed (CIP) ZrO<sub>2</sub> engineering ceramic was conducted to investigate the individual differences of laser brightness (radiance) produced by the two laser sources. The effects of brightness exhibited by the two lasers were investigated in respect to the change in the hardness, dimensional size of the laser irradiated zones and the microstructure of the ZrO<sub>2</sub> engineering ceramic. The results showed that the hardness of the ZrO<sub>2</sub> engineering ceramic was reduced by 36% for the Nd:YAG laser in comparison to the as-received surface. However, only 4% reduction in the surface hardness was found from employing the fibre laser surface treatment which was not significant as much as the results of the Nd:YAG laser irradiation. The change in hardness occurred due to softening of the laser irradiated surface of the ZrO<sub>2</sub> with a changed composition which was softer than the laser unaffected surface. The dimensional size of the fibre laser irradiated track was also found to produce broader surface profiles in comparison to that of the Nd:YAG laser. The fibre laser irradiated surface track was 32% larger in width and 51.5% longer in depth of penetration in comparison to that of the Nd:YAG laser. Change in microstructure of the ZrO2 engineering ceramic irradiated by both lasers was found as opposed to the ground and polished untreated surface. The fibre laser affected the grain morphology to a greater extent in comparison to that of the Nd:YAG laser irradiation. The physical and micro-structural effects from applying the two laser types to the ZrO<sub>2</sub> engineering ceramic differed as deep penetration and broader laser irradiated track as well as larger grains were produced by the fibre laser, despite using identical laser processing parameters such as spot size, power density, traverse speed, gas flow rate, wavelength and the Gaussian beam profile. This occurred due to the high brightness exhibited by the fibre laser irradiation which generated larger power per unit area which in turn induced into the ZrO<sub>2</sub> engineering ceramic and resulted to producing high processing temperature, larger fibre laser-ceramic-interaction zone and melt-pool at the laser-ZrO<sub>2</sub> interface in comparison to that of the Nd:YAG laser which intrinsically resulted to a change in physical attributes of the ceramic.