| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Jamian, Saifulnizan
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2021Study on FGNF/epoxy Composite Fabricated by Using Centrifugal Slurry-Pouring Method
- 2020Damage Initiation and Evolution Analysis of Hot Extruded Recycled Aluminium Alloys (AA6061)citations
- 2020Characterisation of Electrode Drying Effect on the Tungsten Carbide Hardfacing Microstructure
- 2020Characterization of Continuous Gradient Functionally Graded Natural Fiber Reinforced Polymer Compositescitations
- 2020HAp Coated Hip Prosthesis Contact Pressure Prediction Using FEM Analysiscitations
- 2017Effect of Rotating Mold Speed on Microstructure of Al LM6 Hollow Cylinder Fabricated Using Centrifugal Methodcitations
- 2017Deflection of elastic beam with SMA wires eccentrically insertedcitations
- 2017Residual stresses in shape memory alloy fiber reinforced aluminium matrix compositecitations
- 2016Fracture toughness of woven kenaf fibre reinforced compositescitations
- 2015AI LM6 hollow cylinder fabricated using centrifugal casting
- 2015FABRICATION OF FUNCTIONALLY GRADED NATURAL FIBRE/EPOXY CYLINDER USING CENTRIFUGAL CASTING METHOD
- 2015Effect of welding heat input on microstructure and mechanical properties at coarse grain heat affected zone of ABS grade a steel
- 2015FGNF/EPOXY COMPOSIT FABRICATE USING CENTRIFUGAL SLURRY-POURING METHOD
- 2012Application of functionally graded materials for severe plastic deformation and smart materials : experimental study and finite element analysis
- 2012Experimental Study on Severe Plastic Deformation of Ti by Novel Equal-Channel Angular Pressingcitations
- 2007FUNDAMENTAL FREQUENCY OF HYBRID COMPOSITE PLATE EMBEDDED WITH SHAPE MEMORY ALLOY WIRE
Places of action
| Organizations | Location | People |
|---|
document
AI LM6 hollow cylinder fabricated using centrifugal casting
Abstract
The main purpose of this study was to investigate the silicon (Si) particles distribution of Al LM6 cylinderproduced by centrifugal casting method. Al LM6 cylinder fabrication started by melting Al LM6 ingots. The melt is thenpoured into a rotating mould with constant speed of 1700 rpm (100 times of gravity value, 100G) at room temperature.After five hours left to freeze, LM6 Al cylinder is removed from the mold. The result is an Al LM6 hollow cylinder withthe outer and inner diameter of 60 and 20 mm, respectively and the thickness of 35 mm. The temperatures of the molteningot used in this study were 690, 710 and 725°C. The microstructure differences due to different melting temperaturesobserved using an optical microscope (OM). Microstructural observations show that the Si particles content are almost thesame on the inside, center and outside the specimen. However, the sizes of Si particles in these three parts are different.The particle size of the specimens has a size larger than in the middle and the outside. The difference in size is due to thelow density of Si particles than Al and the expansion of Si particles due to rapid melt cooling rate in the mold duringcentrifugal casting process. The three specimens with different values of melt temperature shows different size Si particles.The difference of Si particle size and distribution expected will influences the mechanical properties of Al LM6 fabricated.