| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Andersen, Tom Løgstrup
Technical University of Denmark
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (19/19 displayed)
- 2024A Precise Prediction of the Chemical and Thermal Shrinkage during Curing of an Epoxy Resin
- 2023Biobased composites: materials, properties, and potential applications as wind turbine blade materialscitations
- 2023Cure characterisation and prediction of thermosetting epoxy for wind turbine blade manufacturingcitations
- 2023The impact of the fiber volume fraction on the fatigue performance of glass fiber compositescitations
- 2022Observation of the interaction between transverse cracking and fibre breaks in uni-directional non-crimp fabric composites subjected to cyclic bending fatigue damage mechanismcitations
- 2016Investigation of Mechanical Properties of Unidirectional Steel Fiber/Polyester Composites: Experiments and Micromechanical Predictionscitations
- 2015Impact of non-hookean behaviour on mechanical performance of hybrid composites
- 2014Effect of Polymer Form and its Consolidation on Mechanical Properties and Quality of Glass/PBT Compositescitations
- 2013Influence of Temperature on Mechanical Properties of Jute/Biopolymer Compositescitations
- 2012Attribute Based Selection of Thermoplastic Resin for Vacuum Infusion Process: A Decision Making Methodology
- 2012Experimental Determination and Numerical Modelling of Process Induced Strains and Residual Stresses in Thick Glass/Epoxy Laminate
- 2012In situ measurement using FBGs of process-induced strains during curing of thick glass/epoxy laminate platecitations
- 2011Influence of moisture absorption on properties of fiber reinforced polyamide 6 composites
- 2011A New Static and Fatigue Compression Test Method for Compositescitations
- 2011Attribute based selection of thermoplastic resin for vacuum infusion processcitations
- 2009Pin-on-disk apparatus for tribological studies of polymeric materialscitations
- 2008Changes in the tribological behavior of an epoxy resin by incorporating CuO nanoparticles and PTFE microparticlescitations
- 2008The effect of particle addition and fibrous reinforcement on epoxy-matrix composites for severe sliding conditionscitations
- 2002Influence of fiber type, fiber mat orientation, and process time on the properties of a wood fiber/polymer compositecitations
Places of action
| Organizations | Location | People |
|---|
document
Impact of non-hookean behaviour on mechanical performance of hybrid composites
Abstract
Hybrid composites, based on unidirectional fibres of carbon and glass, in an epoxy matrix have been used to investigate the possibility of a hybrid effect. The hybrid effect is observed experimentally by values for both composite strength and composite failure strain, which are increased compared to a simple model. The introduction of an increase of the failure strain of the carbon fibre part (the “fibre”) of the composite, described by a factor H for the increase of the failure strain, results in theoretical curves for strength and failure strain, which are in general agreement with the experimental data. For the present hybrid composites a value of 푯 = ퟏ.ퟐퟐ is required, meaning a positive hybrid effect on “fibre” strain of 22%. It is thus concluded that the simple concept of a hybrid factor H for the fibre failure strain can describe the observed hybrid effect satisfactorily.