| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Lecis, Nora
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (10/10 displayed)
- 2024Influence of Thermomechanical Treatments and Chemical Composition on the Phase Transformation of Cu-Al-Mn Shape Memory Alloy Thin Sheets
- 2024Analysis of the causes determining dimensional and geometrical errors in 316L and 17-4PH stainless steel parts fabricated by metal binder jettingcitations
- 2024Design challenges in leveraging binder jetting technology to innovate the medical instrument fieldcitations
- 2024Friction and wear performance of polyether ether ketone (PEEK) polymers in three lubrication regimescitations
- 2023Effects Of Feedstock Morphology And Composition On Binder Jetting Of 316L Stainless Steel: A Perspective On Circular Economy
- 2023Influence of shape distortion on the precision of holes in parts fabricated by Metal Binder Jettingcitations
- 20213D printing of fine alumina powders by binder jettingcitations
- 2021Tribological Characterization of Polyether Ether Ketone (PEEK) Polymers Produced by Additive Manufacturing for Hydrodynamic Bearing Applicationcitations
- 2021Mechanical and microstructural characterization of WC-Co consolidated by binder jetting additive manufacturingcitations
- 2012Creep behaviour of deep cryogenic treated AZ91 magnesium alloy
Places of action
| Organizations | Location | People |
|---|
document
Effects Of Feedstock Morphology And Composition On Binder Jetting Of 316L Stainless Steel: A Perspective On Circular Economy
Abstract
<jats:p>Binder jetting is a sinter-based technique that allows the production of application-oriented designs with a reduced consumption of raw materials. The employment of powders from scrap metal recycling would minimise the lifecycle impact of the process. In our work, gas atomised powders tailored for binder jetting are compared to a feedstock obtained by recycling of 316L waste. The morphological features of particles, especially sphericity and size distribution, are measured by granulometry and scanning electron microscopy. Printed components are studied at the green and sintered state to observe the influence of each feedstock and the comparative analyses on density and final microstructures (residual porosity, grain size and phases distribution) allows to determine which are the most beneficial properties of the powders. CALPHAD modelling highlights the feedstock chemical composition effects on densification mechanisms: Ni and C content are responsible for δ phase formation and solidus temperature, thus affecting diffusive processes during sintering.</jats:p>