693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Blackwell, Paul
University of Strathclyde
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (41/41 displayed)
- 2023Integrating HIP and homogenisation heat treatment and its effect on the workability of a conventional peritectic TiAl alloycitations
- 2023Improving forging outcomes of cast titanium aluminide alloy via cyclic induction heat treatment
- 2023Influence of mesh in modelling of flow forming process
- 2022Tailoring titanium sheet metal using laser metal deposition to improve room temperature single-point incremental formingcitations
- 2021Effect of machining induced microstructure changes on the edge formability of titanium alloys at room temperature
- 2021A new route for developing ultrafine-grained Al alloy strips using repetitive bending under tensioncitations
- 2021Influence of longitudinal scratch defects on the bendability of titanium alloycitations
- 2020Formability of AA-7075 sheets subjected to repetitive bending under tension
- 2020Influence of sheet conditions on in-plane strain evolution via ex-situ tensile deformation of Ti-3Al-2.5V at room temperaturecitations
- 2020Examining failure behaviour of commercially pure titanium during tensile deformation and hole expansion testcitations
- 2020Influence of laser power and powder feed rate on the microstructure evolution of laser metal deposited Ti-5553 on forged substratescitations
- 2020Mechanical response and microstructure evolution of commercially pure titanium subjected to repetitive bending under tensioncitations
- 2020Aspects of high strain rate industrial forging of Inconel 718
- 2020Impact of machining induced surface defects on the edge formability of commercially pure titanium sheet at room temperaturecitations
- 2020Superplastic behaviour of Ti54M and Ti64citations
- 2019Effect of edge conditions on the formability of commercially pure titanium sheet (Grade 2) at room temperature
- 2019Superplastic behaviour of Ti54M and Ti64
- 2018Studies on Ti54M Titanium Alloy for Application within the Aerospace Industry
- 2018The effect of elasto-plastic properties of materials on their formability by flow formingcitations
- 2018Studies on titanium alloys for aerospace applicationcitations
- 2018Studies on titanium alloys for aerospace applicationcitations
- 2017Al-Li Alloys – The Analysis of Material Behaviour during Industrial Hot Forgingcitations
- 2017On the specifics of modelling of rotary forging processes
- 2017A dynamic model for simulation of hot radial forging processcitations
- 2017Microstructure and residual stress in Ti-6l-4V parts made by different additive manufacturing techniques
- 2017Al-Li Alloys : The Analysis of Material Behaviour during Industrial Hot Forgingcitations
- 2016β Recrystallisation characteristics of α + β titanium alloys for aerospace applicationscitations
- 2016Modelling microstructure evolution in ATI 718Plus® alloy
- 2016An approach to microstructure modelling in nickel based superalloys
- 2016Wear behaviour of laser cladded Ni-based WC composite coating for Inconel hot extrusion
- 2016Effect of plastic deformation on elastic and plastic recovery in CP-Titaniumcitations
- 2016The development of stress based continuum damage mechanics model for predicting the formability of Magnesium alloys under cold/warm stamping processes
- 2016The mechanics of superplastic formingcitations
- 2016Microstructure and residual stress in Ti-6l-4V parts made by different additive manufacturing techniques
- 2016Feasibility study of complex sheet hydroforming processcitations
- 2015Simulation of the material softening during hot metal formingcitations
- 2014Improvement in ductility in commercially pure titanium alloys by stress relaxation at room temperaturecitations
- 2014Modelling of active transformation of microstructure of two-phase Ti alloys during hot workingcitations
- 2013Modelling the superplastic forming of a multi-sheet diffusion bonded titanium alloy demonstrator fan bladecitations
- 2005Laser-aided manufacturing technologies; their application to the near-net shape forming of high-strength titanium alloycitations
- 2000Superplastic behaviour of Inconel 718 sheetcitations
Places of action
| Organizations | Location | People |
|---|
article
Modelling the superplastic forming of a multi-sheet diffusion bonded titanium alloy demonstrator fan blade
Abstract
The paper describes a finite element method in 2D and 3D to simulate the super plastic forming of a demonstrator jet engine fan blade made from Titanium alloy sheet. The fan blade is an assembly of three sheets in which a single inner (core) sheet is diffusion bonded to the two outer (skin) sheets at prescribed zones, which is then super-plastically formed to a desired fan profile. In the model, the diffusion bonded zones between the core and skin sheets are simulated using tied interfaces. The thickness of each skin sheet is not uniform and significant change in thickness can occur over a short distance as well as gradually over the entire skin sheet. The thickness of the core sheet which is smaller than the thickness of each skin sheet remains uniform. The paper describes the design for a scaled-down demonstrator fan blade and model build process. Selected results and evaluations of finite element simulations are presented and discussed.