| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Sia, Chee Kiong
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (11/11 displayed)
- 2019Performance Properties Optimization of Triaxial Ceramic-Palm Oil Fuel Ash By Employing Taguchi Grey Relational Analysis
- 2017Optimization of the EMI shielding effectiveness of fine and ultrafine POFA powder mix with OPC powder using Flower Pollination Algorithmcitations
- 2014Iron Oxide Rust as Raw Material for the Production of Red Pigment in Paint Industrycitations
- 2014Preparation of Palm Oil Fuel Ash Composite as Green Pigmentcitations
- 2013An Exploration to Develop Concrete Walls Using MnxZn1-xFe2O4 Ferrite as Absorbing Material to Provide Defense against Electromagnetic Pollutioncitations
- 2013Decision Making With the Analytical Hierarchy Process (AHP) for Material Selection in Screw Manufacturing for Minimizing Environmental Impactscitations
- 2013Feasibility Study of Waste Motor Recycling through Manual Dismantling and Hydrometallurgical Processcitations
- 2013Characterization of Nickel-Zinc Ferrite Powder Prepared via Sol-Gel Technique in Between 100 MHz to 2 GHz
- 2013Decision Making of Screw Manufacturing for the Best Environmental and Economic Combination by Using AHPcitations
- 2009The magnetic properties of porous Ni-Zn ferrites prepared from wood templatescitations
- 2009Porous Ba Ferrite Prepared from Wood Templatecitations
Places of action
| Organizations | Location | People |
|---|
article
Decision Making of Screw Manufacturing for the Best Environmental and Economic Combination by Using AHP
Abstract
This study is an approach to investigate the viable impacts of screw manufacturing. At the same time, choose the suitable material and selected manufacturing process of screw by considering environmental aspects without sacrificing the economic aspect. It is important to the organisation to improve the environmental aspect. Therefore in this study, the decision making was focused on economic aspects to produce the synergy results between economic and environmental impact. The parameters involved were types of material and manufacturing process of screw which using the available data of environmental and production volume. The two different manufacturing approaches being evaluated were machining and forging process. The types of material concerned for forging process encompassed low carbon steel, alloy steel stainless steel, and aluminium alloy. On the other hand, for machining process, the material being considered in screw manufacturing were cast iron, low carbon steel, alloy steel, stainless steel and aluminium alloy. The information of environmental impacts that generated from SolidWorks Sustainability tool and screw production cost were calculate using Manufacturing cost model, both information was used in Analytic Hierarchy Process (AHP) analysis to obtain local priority of economic and environmental impacts. Then, the ranking of both global and local priorities from economic impact and environmental impacts had enabled the determination of appropriate material used for those selected screw manufacturing process. As result, low carbon steel was chosen for forging process whereas cast iron was excelled in machining process, at the same time, stainless steel was not suggested to be used in both two processes.