| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Nor, Nik Hisyamudin Muhd
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (11/11 displayed)
- 2017Optimization of the EMI shielding effectiveness of fine and ultrafine POFA powder mix with OPC powder using Flower Pollination Algorithmcitations
- 2017Effects of Annealing Time on Electrodeposited-n-Cu2O Thin Film
- 2017Effect of triggering angles on the crushing mechanisms of hybrid woven kenaf/aluminum hollow cylinders
- 2017Effect of Rotating Mold Speed on Microstructure of Al LM6 Hollow Cylinder Fabricated Using Centrifugal Methodcitations
- 2017Deflection of elastic beam with SMA wires eccentrically insertedcitations
- 2017Cyclic Voltammetry Measurement for Cu2O Based Homostructure Thin Filmcitations
- 2017Residual stresses in shape memory alloy fiber reinforced aluminium matrix compositecitations
- 2016Fracture toughness of woven kenaf fibre reinforced compositescitations
- 2013Decision Making With the Analytical Hierarchy Process (AHP) for Material Selection in Screw Manufacturing for Minimizing Environmental Impactscitations
- 2013Feasibility Study of Waste Motor Recycling through Manual Dismantling and Hydrometallurgical Processcitations
- 2013Decision Making of Screw Manufacturing for the Best Environmental and Economic Combination by Using AHPcitations
Places of action
| Organizations | Location | People |
|---|
article
Decision Making of Screw Manufacturing for the Best Environmental and Economic Combination by Using AHP
Abstract
This study is an approach to investigate the viable impacts of screw manufacturing. At the same time, choose the suitable material and selected manufacturing process of screw by considering environmental aspects without sacrificing the economic aspect. It is important to the organisation to improve the environmental aspect. Therefore in this study, the decision making was focused on economic aspects to produce the synergy results between economic and environmental impact. The parameters involved were types of material and manufacturing process of screw which using the available data of environmental and production volume. The two different manufacturing approaches being evaluated were machining and forging process. The types of material concerned for forging process encompassed low carbon steel, alloy steel stainless steel, and aluminium alloy. On the other hand, for machining process, the material being considered in screw manufacturing were cast iron, low carbon steel, alloy steel, stainless steel and aluminium alloy. The information of environmental impacts that generated from SolidWorks Sustainability tool and screw production cost were calculate using Manufacturing cost model, both information was used in Analytic Hierarchy Process (AHP) analysis to obtain local priority of economic and environmental impacts. Then, the ranking of both global and local priorities from economic impact and environmental impacts had enabled the determination of appropriate material used for those selected screw manufacturing process. As result, low carbon steel was chosen for forging process whereas cast iron was excelled in machining process, at the same time, stainless steel was not suggested to be used in both two processes.