| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Ramos, As
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (4/4 displayed)
- 2022Joining of Ti6Al4V to Al2O3 Using Nanomultilayerscitations
- 2021Joining Ti6Al4V to Alumina by Diffusion Bonding Using Titanium Interlayerscitations
- 2021Diffusion Bonding of Ti6Al4V to Al2O3 Using Ni/Ti Reactive Multilayerscitations
- 2020Effect of Deposition Parameters on the Reactivity of Al/Ni Multilayer Thin Filmscitations
Places of action
| Organizations | Location | People |
|---|
article
Joining Ti6Al4V to Alumina by Diffusion Bonding Using Titanium Interlayers
Abstract
This work aims to investigate the joining of Ti6Al4V alloy to alumina by diffusion bonding using titanium interlayers: thin films (1 mu m) and commercial titanium foils (5 mu m). The Ti thin films were deposited by magnetron sputtering onto alumina. The joints were processed at 900, 950, and 1000 & DEG;C, dwell time of 10 and 60 min, under contact pressure. Experiments without interlayer were performed for comparison purposes. Microstructural characterization of the interfaces was conducted by optical microscopy (OM), scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), and electron backscatter diffraction (EBSD). The mechanical characterization of the joints was performed by nanoindentation to obtain hardness and reduced Young's modulus distribution maps and shear strength tests. Joints processed without interlayer have only been achieved at 1000 & DEG;C. Conversely, joints processed using Ti thin films as interlayer showed promising results at temperatures of 950 & DEG;C for 60 min and 1000 & DEG;C for 10 and 60 min, under low pressure. The Ti adhesion to the alumina is a critical aspect of the diffusion bonding process and the joints produced with Ti freestanding foils were unsuccessful. The nanoindentation results revealed that the interfaces show hardness and reduced Young modulus, which reflect the observed microstructure. The average shear strength values are similar for all joints tested (52 & PLUSMN; 14 MPa for the joint processed without interlayer and 49 & PLUSMN; 25 MPa for the joint processed with interlayer), which confirms that the use of the Ti thin film improves the diffusion bonding of the Ti6Al4V alloy to alumina, enabling a decrease in the joining temperature and time.