| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Aamir, Muhammad
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (15/15 displayed)
- 2024Mechanical Properties and Microstructural Investigation of AA2024-T6 Reinforced with Al2O3 and SiC Metal Matrix Compositescitations
- 2023Recent advances in the synthesis of ZnO-based electrochemical sensorscitations
- 2021Effect of seawater ageing on fracture toughness of stitched glass fiber/epoxy laminates for marine applicationscitations
- 2021Managing risks in the improved model of rolling mill loading: a case studycitations
- 2021The effect of TiN-, TiCN-, TiAlN-, and TiSiN coated tools on the surface defects and geometric tolerances of holes in multi-spindle drilling of Al2024 alloycitations
- 2021Irregularity Measures of Subdivision Vertex-Edge Join of Graphs
- 2021Measurement of micro burr and slot widths through image processing: comparison of manual and automated measurements in micro-millingcitations
- 2021Relationship between pressure and output parameters in belt grinding of steels and nickel alloycitations
- 2020Sequential damage study induced in fiber reinforced composites by shear and tensile stress using a newly developed Arcan fixturecitations
- 2020Superior visible-light assisted water splitting performance by Fe incorporated ZnO photoanodescitations
- 2019Fabrication of Ni 2+ incorporated ZnO photoanode for efficient overall water splittingcitations
- 2018Bis(selenobenzoato)dibutyltin(iv) as a single source precursor for the synthesis of SnSe nanosheets and their photo-electrochemical study for water splittingcitations
- 2018Novel single source precursor for synthesis of Sb2Se3 nanorods and deposition of thin films by AACVD: Photo-electrochemical study for water reduction catalysiscitations
- 2017Synthesis of Hybrid to Inorganic Quasi 2D-Layered Perovskite Nanoparticlescitations
- 2016A chemodosimetric approach for the selective detection of Pb2+ ions using a cesium based perovskitecitations
Places of action
| Organizations | Location | People |
|---|
article
Relationship between pressure and output parameters in belt grinding of steels and nickel alloy
Abstract
Belt grinding of flat surfaces of typical parts made of steel and alloys, such as grooves, shoulders, ends, and long workpieces, is a good alternative to milling. Several factors can influence the belt grinding process of flat surfaces of metals, such as cutting speed and pressure. In this work, the importance of pressure in the belt grinding was investigated in terms of technological and experimental aspects. The grinding experiments were performed on structural alloy steel 30KhGSN2/30KhGSNA, structural carbon steel AISI 1045, corrosion-resistant and heat-resistant stainless steel AISI 321, and heat-resistant nickel alloy KHN77TYuR. The performance of the grinding belt was investigated in terms of surface roughness, material removal rate (MRR), grinding belt wear, performance index. Estimated indicators of the belt grinding process were developed: cutting ability; reduced cutting ability for belt grinding of steels and heat-resistant alloy. It was found that with an increase in pressure p, the surface roughness of the processed surface Ra decreased while the tool wear VB and MRR increased. With a decrease in plasticity and difficulty of machinability, the roughness, material removal rate, reduced cutting capacity (Performance index) qper, material removal Q decreased, and the tool wear VB increased. The obtained research results can be used by technologists when creating belt grinding operations for steels and alloys to ensure the required performance is met.