| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Chromiński, Witold
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (19/19 displayed)
- 2024Albumin suppresses oxidation of Ti-Nb alloy in the simulated inflammatory environment
- 2021Microstructure, Texture and Mechanical Properties of Mg-6Sn Alloy Processed by Differential Speed Rollingcitations
- 2019Investigation of different severe plastic deformation methods effect on Ti13Nb13Zr
- 2019Tribological behavior of a hydrostatically extruded ultra-fine grained Ti-13Nb-13Zr alloycitations
- 2019The importance of microstructural heterogeneities in the work hardening of ultrafine-grained aluminum, studied by in-situ TEM straining and mechanical testscitations
- 2018Enhanced strength and electrical conductivity of ultrafine-grained Al-Mg-Si alloy processed by hydrostatic extrusioncitations
- 2018Mechanisms of plastic deformation in ultrafine-grained aluminium – In-situ and ex-post studiescitations
- 2017Ultrafine-Grained Plates of Al-Mg-Si Alloy Obtained by Incremental Equal Channel Angular Pressing: Microstructure and Mechanical Propertiescitations
- 2017Microstructure and Texture Evolutions of Biomedical Ti-13Nb-13Zr Alloy Processed by Hydrostatic Extrusioncitations
- 2017Mechanical properties and corrosion resistance of ultrafine grained austenitic stainless steel processed by hydrostatic extrusioncitations
- 2017Accumulation and mechanism of the fatigue damage for a nickel based superalloy
- 2017Evaluation of mechanical properties and anisotropy of ultra-fine grained 1050 aluminum sheets produced by incremental ECAPcitations
- 2016Mechanical properties, structural and texture evolution of biocompatible Ti–45Nb alloy processed by severe plastic deformationcitations
- 2016Incremental ECAP as a method to produce ultrafine grained aluminium platescitations
- 2015Microstructure evolution in aluminium 6060 during Incremental ECAP
- 2015Efficient method of producing ultrafine grained non-ferrous metals
- 2015Grain refinement in technically pure aluminium plates using incremental ECAP processingcitations
- 2014Enhancement of mechanical properties of biocompatible Ti-45Nb alloy by hydrostatic extrusioncitations
- 2014Incremental ECAP as a novel tool for producing ultrafine grained aluminium platescitations
Places of action
| Organizations | Location | People |
|---|
article
Microstructure, Texture and Mechanical Properties of Mg-6Sn Alloy Processed by Differential Speed Rolling
Abstract
The effect of shear deformation introduced by differential speed rolling (DSR) on the microstructure, texture and mechanical properties of Mg-6Sn alloy was investigated. Mg-6Sn sheets were obtained by DSR at speed ratio between upper and lower rolls of R = 1, 1.25, 2 and 3 (R = 1 refers to symmetric rolling). The microstructural and textural changes were investigated by electron backscattered diffraction (EBSD) and XRD, while the mechanical performance was evaluated based on tensile tests and calculated Lankford parameters. DSR resulted in the pronounced grain refinement of Mg-6Sn sheets and spreading of basal texture as compared to conventionally rolled one. The average grain size and basal texture intensity gradually decreased with increasing speed ratio. The basal poles splitting to transverse direction (TD) or rolling direction (RD) was observed for all Mg-6Sn sheets. For the as-rolled sheets, YS and UTS increased with increasing speed ratio, but a significant anisotropy of strength and ductility between RD and TD has been observed. After annealing at 300 °C, Mg-6Sn sheets became more homogeneous, and the elongation to failure was increased with higher speed ratios. Moreover, the annealed Mg-6Sn sheets were characterized by a very low normal anisotropy (0.91–1.16), which is normally not achieved for the most common Mg-Al-Zn alloys.