| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Majchrowicz, Kamil
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2024Mechanical recycling of CFRPs based on thermoplastic acrylic resin with the addition of carbon nanotubescitations
- 2024A novel approach to enhance mechanical properties of Ti substrates for biomedical applicationscitations
- 2023The influence of microstructure and texture on the hardening by annealing effect in cold-rolled titaniumcitations
- 2022Comparison of Microstructure, Texture, and Mechanical Properties of TZ61 and AZ61 Mg Alloys Processed by Differential Speed Rollingcitations
- 2022Surface Properties and Mechanical Performance of Ti-Based Dental Materials: Comparative Effect of Valve Alloying Elements and Structural Defectscitations
- 2022The Influence of Heat Treatment on the Mechanical Properties and Corrosion Resistance of the Ultrafine-Grained AA7075 Obtained by Hydrostatic Extrusioncitations
- 2022The Impact of Retained Austenite on the Mechanical Properties of Bainitic and Dual Phase Steelscitations
- 2021Studies of Bainitic Steel for Rail Applications Based on Carbide-Free, Low-Alloy Steelcitations
- 2021Microstructure, Texture and Mechanical Properties of Mg-6Sn Alloy Processed by Differential Speed Rollingcitations
- 2021Influence of microstructural features on the growth of nanotubular oxide layers on β-phase Ti-24Nb-4Zr-8Sn and α + β-phase Ti-13Nb-13Zr alloyscitations
- 2019Exploring the susceptibility of P110 pipeline steel to stress corrosion cracking in CO2-rich environmentscitations
- 2019Microstructure and mechanical properties of Ti–Re alloys manufactured by selective laser meltingcitations
- 2018Hot Corrosion of Ti–Re Alloys Fabricated by Selective Laser Meltingcitations
- 2018The Effect of Rhenium Addition on Microstructure and Corrosion Resistance of Inconel 718 Processed by Selective Laser Meltingcitations
- 2018Fatigue behavior of 6xxx aluminum alloy processed by severe plastic deformation
- 2018Enhanced strength and electrical conductivity of ultrafine-grained Al-Mg-Si alloy processed by hydrostatic extrusioncitations
Places of action
| Organizations | Location | People |
|---|
article
Microstructure, Texture and Mechanical Properties of Mg-6Sn Alloy Processed by Differential Speed Rolling
Abstract
The effect of shear deformation introduced by differential speed rolling (DSR) on the microstructure, texture and mechanical properties of Mg-6Sn alloy was investigated. Mg-6Sn sheets were obtained by DSR at speed ratio between upper and lower rolls of R = 1, 1.25, 2 and 3 (R = 1 refers to symmetric rolling). The microstructural and textural changes were investigated by electron backscattered diffraction (EBSD) and XRD, while the mechanical performance was evaluated based on tensile tests and calculated Lankford parameters. DSR resulted in the pronounced grain refinement of Mg-6Sn sheets and spreading of basal texture as compared to conventionally rolled one. The average grain size and basal texture intensity gradually decreased with increasing speed ratio. The basal poles splitting to transverse direction (TD) or rolling direction (RD) was observed for all Mg-6Sn sheets. For the as-rolled sheets, YS and UTS increased with increasing speed ratio, but a significant anisotropy of strength and ductility between RD and TD has been observed. After annealing at 300 °C, Mg-6Sn sheets became more homogeneous, and the elongation to failure was increased with higher speed ratios. Moreover, the annealed Mg-6Sn sheets were characterized by a very low normal anisotropy (0.91–1.16), which is normally not achieved for the most common Mg-Al-Zn alloys.