| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Bahrami, Abbas
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (17/17 displayed)
- 2023Electrophoretic Deposition of ZnO-Containing Bioactive Glass Coatings on AISI 316L Stainless Steel for Biomedical Applicationscitations
- 2023Failure Analysis of Two HP-Nb Heat-Resistant Tubes after 46,000 h Exposure to Reformer Service Conditionscitations
- 2022Synthesis and characterization of Ag-ion-exchanged zeolite/TiO2 nanocomposites for antibacterial applications and photocatalytic degradation of antibioticscitations
- 2021Facile synthesis of ag nanowire/tio2 and ag nanowire/tio2/go nanocomposites for photocatalytic degradation of rhodamine bcitations
- 2021Facile synthesis of ag nanowire/tio2 and ag nanowire/tio2/go nanocomposites for photocatalytic degradation of rhodamine bcitations
- 2020Corrosion-Fatigue Failure of Gas-Turbine Blades in an Oil and Gas Production Plantcitations
- 2019Creep Failure of Reformer Tubes in a Petrochemical Plantcitations
- 2019Precipitation in Al–Mg–Si Alloys: Modeling
- 2019Root Cause Analysis of Surface Cracks in Heavy Steel Plates during the Hot Rolling Processcitations
- 2019Modeling Electrical Resistivity of Naturally Aged Al–Mg–Si Alloyscitations
- 2019A Study on the Failure of AISI 304 Stainless Steel Tubes in a Gas Heater Unitcitations
- 2019Root cause analysis of surface cracks in heavy steel plates during the hot rolling processcitations
- 2019Modeling electrical resistivity of naturally aged Al–Mg–Si Alloyscitations
- 2019Towards a high strength ductile Ni/Ni3Al/Ni multilayer composite using spark plasma sinteringcitations
- 2019Wear Induced Failure of Automotive Disc Brakes—A Case Studycitations
- 2019A study on the failure of AISI 304 stainless steel tubes in a gas heater unitcitations
- 2017Microstructural characteristics of nano-structured Fe-28.5Ni steel by means of severe plastic deformationcitations
Places of action
| Organizations | Location | People |
|---|
article
Wear Induced Failure of Automotive Disc Brakes—A Case Study
Abstract
<jats:p>This paper investigated a failure in a ventilated disc brake in an automobile. The failed brake disc had been in service for approximately 10 years. The observed failure was in the form of radial cracks that appeared to have initiated at the outer edge of the disc brake. The cracks were rather straight with no branching. Optical microscope, scanning electron microscope (SEM), and energy dispersive X-ray spectroscopy (EDS) were used to study the microstructure of the failed disc. Vickers microhardness test was also used to evaluate the hardness of the samples. Results showed that the root cause of crack formation, in this case, was related to the excessive wear in the brake disc. Different wear mechanisms, namely abrasive and adhesive wear, were recognized in the failed specimen. Moreover, the worn surface in some areas was covered with fine oxide particles. These particles appeared to have a significant contribution toward abrasion. To further understand the wear mechanisms, pin-on-disc experiments were also conducted on the samples. Results of the pin-on-disc experiments were compared and correlated to the results obtained from the failed brake disc.</jats:p>