| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Kwame, James
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (11/11 displayed)
- 2021Effect of machining induced microstructure changes on the edge formability of titanium alloys at room temperature
- 2021Influence of longitudinal scratch defects on the bendability of titanium alloycitations
- 2020Influence of sheet conditions on in-plane strain evolution via ex-situ tensile deformation of Ti-3Al-2.5V at room temperaturecitations
- 2020Examining failure behaviour of commercially pure titanium during tensile deformation and hole expansion testcitations
- 2020Impact of machining induced surface defects on the edge formability of commercially pure titanium sheet at room temperaturecitations
- 2019Superplasticity of Ti-6Al-4V Titanium Alloy: Microstructure Evolution and Constitutive Modellingcitations
- 2019Superplastic deformation behavior of ultra-fine-grained Ti-1V-4Al-3Mo alloycitations
- 2019Experimental, modelling and simulation of an approach for optimizing the superplastic forming of Ti-6%Al-4%V titanium alloycitations
- 2019Effect of edge conditions on the formability of commercially pure titanium sheet (Grade 2) at room temperature
- 2017Superplastic deformation behaviour and microstructure evolution of near-α Ti-Al-Mn alloycitations
- 2017Modelling of the superplastic deformation of the near-a titanium alloy (Ti-2.5AL-1.8MN) using arrhenius-type constitutive model and artificial neural networkcitations
Places of action
| Organizations | Location | People |
|---|
article
Examining failure behaviour of commercially pure titanium during tensile deformation and hole expansion test
Abstract
Hole expansion ratio is a material parameter which defines the extent to which sheet metals are formed. Research has shown that, the stress state observed at the hole edge after hole expansion test is similar to those observed during conventional uniaxial tensile test. However, conventional tensile test methods are not efficient in evaluating material edge formability. This work utilised optical non-contact measuring techniques to examine failure behaviour during tensile test and hole expansion test of commercially pure titanium sheet, fabricated with either abrasive water jet cutting or electric discharge machining. The work found that, the deformation mode in conventional tensile testing are governed by localised necking and subsequently diffused necking prior to failure. Deformation mode observed in hole expansion test is characterised by localised necking with no visible occurrence of diffused necking prior to failure. The highest strains are concentrated at the hole edge during hole expansion test due to their sensitivity to the hole preparation method with accompanying multiple localised necking sites resulting in non-uniform deformation. Strains become concentrated in the bulk material microstructure rather than the machined edge during tensile testing resulting in single localised deformation site and a more homogenous deformation.