| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Avanzini, Andrea
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (14/14 displayed)
- 2022Anisotropic Behaviour of Extruded Short Carbon Fibre Reinforced PEEK Under Static and Fatigue Loadingcitations
- 2022Microstructural, Mechanical, and Tribological Evolution under Different Heat Treatment Conditions of Inconel 625 Alloy Fabricated by Selective Laser Melting.citations
- 2022Microstructural, Mechanical, and Tribological Characterization of Selective Laser Melted CoCrMo Alloy under Different Heat Treatment Conditions and Hot Isostatic Pressing.citations
- 2022Static and fatigue behavior in presence of notches for polyamide 12 (PA12) additively manufactured via Multi Jet Fusion™ processcitations
- 2021Microstructural, Mechanical, and Tribological Characterization of Selective Laser Melted CoCrMo Alloy under Different Heat Treatment Conditions and Hot Isostatic Pressingcitations
- 2019Evaluation on the fatigue behavior of sand-blasted AlSi10Mg obtained by DMLScitations
- 2019Investigation on fatigue strength of sand-blasted DMLS-AlSi10Mg alloycitations
- 2018Influence of micro-notches on the fatigue strength and crack propagation of unfilled and short carbon fiber reinforced PEEKcitations
- 2017INFLUENCE of LEAFLET'S MATRIX STIFFNESS and FIBER ORIENTATION on the OPENING DYNAMICS of A PROSTHETIC TRILEAFLET HEART VALVEcitations
- 2016Shape memory behavior of epoxy-based model materials: Tailoring approaches and thermo-mechanical modelingcitations
- 2013Fatigue behavior and cyclic damage of peek short fiber reinforced compositescitations
- 2011Effect of cyclic strain on the mechanical behavior of a thermoplastic polyurethanecitations
- 2010Failure analysis and life prediction of polymeric rollers for industrial applicationscitations
- 2005Mechanical characterization and modeling of polymeric materials for high pressure sealing
Places of action
| Organizations | Location | People |
|---|
article
Evaluation on the fatigue behavior of sand-blasted AlSi10Mg obtained by DMLS
Abstract
In the present paper, fatigue tests were performed on sand-blasted AlSi10Mg samples produced by Direct Metal Laser Sintering (DMLS). The effect of sand-blasting on surface properties was evaluated by roughness and residual stresses measurements, together with morphological analysis, in comparison with as-built condition. An evident improvement of surface finishing was observed after sand-blasting, which also leaded to the presence of compressive residual stress on the external surface of samples, as revealed by XRD2 measurements. Furthermore, defects analysis allowed the identification of a uniform distribution of porosities in the cross section in terms of number of defects, while larger porosities seem more abundant close to the surface. It was found that the tested material exhibits good fatigue resistance, supporting the positive role of sand-blasting as a simple post-processing treatment. Superficial defects are the preferential crack initiation sites, as demonstrated by SEM analysis of fracture surfaces.