693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Gubeljak, Nenad
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (36/36 displayed)
- 2024Experimental Characterization and Phase-Field Damage Modeling of Ductile Fracture in AISI 316L
- 2024Numerical Simulation of Fatigue Crack Growth and Fracture in Welded Joints Using XFEM—A Review of Case Studiescitations
- 2024A Study on the Compressive Behavior of Additively Manufactured AlSi10Mg Lattice Structurescitations
- 2024SURFACE ROUGHNESS OF Ti6Al4V ALLOY PRODUCED BY LASER POWDER BED FUSIONcitations
- 2023Mechanical performance of hybrid joints of aluminum sheets and laminated beech veneer plates: an experimental prestudycitations
- 2023Rolling Bearing Fault Detection in the Range of Ultrasound
- 2023Microstructure, hardness and fracture resistance of P235TR1 seam steel pipes of different diameters ; Otpornost prema lomu, tvrdoća i mikrostruktura šavnih cevi različitog prečnika izrađenih od čelika P235TR1
- 2023Load-bearing capacity of hybrid riv-bonded aluminum-magnesium joints at quasi-static and cyclic loadingscitations
- 2023Microstructure, hardness and fracture resistance of P235TR1 seam steel pipes of different diameters
- 2023Mechanical performance and failure behavior of screw-bonded joints of aluminum sheets and cross-laminated birch veneer platescitations
- 2023ASSESSMENT OF FATIGUE BEHAVIOUR OF UHSS STEEL BUTT-WELDED JOINTS BY MEANS OF A FRACTURE MECHANICS METHODOLOGY
- 2022Failure assessment of steel pipes using non-standard ring specimens.
- 2022Effects of fixture configurations and weld strength mismatch on J-integral calculation procedure for SE(B) specimenscitations
- 2022Effects of fixture configurations and weld strength mismatch on J-integral calculation procedure for SE(B) specimenscitations
- 2022Effect of welding processes on the fatigue behaviour of ultra-high strength steel butt-welded jointscitations
- 2022Mechanical characterization of surface modified Ti-based alloy before and after severe plastic deformation
- 2022Influence of the Sheet Edge Condition on the Fracture Behavior of Riv-Bonded Aluminum-Magnesium Jointscitations
- 2020Experimental and numerical analysis of tensile properties of Ti-13Nb-13Zr alloy and determination of influence of anodization processcitations
- 2019Crack tip constraint analysis in welded joints with pronounced strength and toughness heterogeneitycitations
- 2018Numerical simulation of fracture in Ti-6Al-4V alloy for orthopedic applications
- 2018Influence of static strength on the fatigue resistance of weldscitations
- 2017Fracture toughness of a high-strength low-alloy steel weldment ; Žilavost loma zvara visokotrdnega malolegiranega jekla
- 2017Experimental determination of fatigue parameters of high chromium steel under different loading and temperature conditions ; Eksperimentalno određivanje parametara zamornog ponašanja visokokromnog lijevanog čelika pri različitim režimima opterećivanja i temperature
- 2016Characterization of heterogeneous arc welds through miniature tensile testing and Vickers hardness mappingcitations
- 2015Measurement of strain caused by residual stresses in a welded joint using neutron diffraction ; Meritev deformacij povzročenih z zaostalimi napetostmi v zvarnem spoju na osnovi nevtronovskega odklona
- 2015Determination of calibration function for fatigue crack propagation by measurment[!] surface deformation
- 2015The effect of a material's heterogeneity on the stress and strain distribution in the vicinity of a crack front ; Vpliv heterogenosti materiala na porazdelitev napetosti in deformacije v bližini razpoke
- 2015Fracture behaviour of thin sheet stainless steel
- 2012Determination of lower bound fracture toughness of a high strength low alloy steel welded joint
- 2012Tensile test models for low-carbon microalloyed steels with high niobium contents ; Modeli za ispitivanje rastezne čvrstoće nisko-ugljičnih mikrolegiranih čelika s visokim sadržajem niobija
- 2012Effect of residual stresses on the fatigue crack propagation in welded joints
- 2012Assessment of the load-bearing capacity of a primary pipeline
- 2012On the local variation of the crack driving force in a double mismatched weld
- 2012Micromechanical analysis of constraint effect on fracture initiation in strength mis-matched welded joints
- 2012The fracture behaviour of global/local mis-matched weld joints provided on HSLA steels ; Pojav loma v globalno/lokalno trdnostno neenakih zvarnih spojih, izvedenih na visokotrdnostnih jeklih
- 2010HIPERC: a novel, high performance, economic steel concept for linepipe and general structural use
Places of action
| Organizations | Location | People |
|---|
article
Microstructure, hardness and fracture resistance of P235TR1 seam steel pipes of different diameters
Abstract
<jats:p>Steel pipelines in industrial plants consist of different elements, includingseamless and/or welded (seam) pipes. Properties of welded pipes, includingtheir fracture behaviour, depend on the characteristics of both, the basemetal, and the weld metal. In this work, two seam pipes are consideredhaving different diameters and manufactured of P235TR1 steel. Hardness andmicrostructure were examined on the samples which contained the seam zone,to capture the influence of heterogeneity. Fracture resistance of thepipeline material, i.e. of both base metals and both seams, was determinedby experimental examination of the recently proposed Pipe ring notch bendingspecimens with sharp stress concentrators. Differences between the twotested pipes, including the influence of the heterogeneity caused by thewelded joint, were determined by comparison of the crack growth resistancecurves. Effects of the initial stress concentrator shape, sharp machinednotch or fatigue pre-crack are discussed.</jats:p>