| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Burnett, Tl
University of Manchester
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (28/28 displayed)
- 2024Exploration of fs-laser ablation parameter space for 2D/3D imaging of soft and hard materials by tri-beam microscopycitations
- 2024Damage evolution in multilayer braided composite tubes under torsion studied by in-situ X-ray Computed Tomography (CT)
- 2024The role of cavitation in the toughening of elastomer nanocomposites reinforced with graphene nanoplateletscitations
- 2023Computational study of the geometrical influence of grain topography on short crack propagation in AA7XXX series alloyscitations
- 2023In situ observation of environmentally assisted crack initiation and short crack growth behaviour of new-generation 7xxx series alloys in humid aircitations
- 2022Large-scale serial sectioning of environmentally assisted cracks in 7xxx Al alloys using femtosecond Laser-PFIBcitations
- 2022Embedded 3D printing of Multi-material composites
- 2022Tailoring the microstructure of lamellar Ti3C2Tx MXene aerogel by compressive strainingcitations
- 2021X-ray Tomographic Observation of Environmental Assisted Cracking in Heat-treated Lean Duplex Stainless Steelcitations
- 2021Multiscale analysis of grain boundary microstructure in high strength 7xxx Al alloyscitations
- 2020Environmentally induced crack (EIC) initiation, propagation, and failure: A 3D in-situ time-lapse study of AA5083 H131citations
- 2020Redistribution of carbon caused by butterfly defects in bearing steelscitations
- 2020Tracking polycrystal evolution non-destructively in 3D by laboratory X-ray diffraction contrast tomographycitations
- 2020X-Ray Tomographic Characterisation of Pitting Corrosion in Lean Duplex Stainless Steelcitations
- 2019On the application of Xe+ plasma FIB for micro-fabrication of small-scale tensile specimenscitations
- 2019Initiation and short crack growth behaviour of environmentally induced cracks in AA5083 H131 investigated across time and length scalescitations
- 2019Completing the picture through correlative characterizationcitations
- 2018Atomic-Scale Insights into the Oxidation of Aluminumcitations
- 2018Multi-Modal Plasma Focused Ion Beam Serial Section Tomography of an Organic Paint Coatingcitations
- 2018Ductile Fracture Assessment of 304L Stainless Steel Using 3D X-ray Computed Tomographycitations
- 2018Realizing the theoretical stiffness of graphene in composites through confinement between carbon fiberscitations
- 2017Degradation of metallic materials studied by correlative tomographycitations
- 2017Time-lapse lab-based X-ray nano-CT study of corrosion damagecitations
- 2017Multiscale correlative tomography: an investigation of creep cavitation in 316 stainless steelcitations
- 2016Xe+ Plasma FIB: 3D Microstructures from Nanometers to Hundreds of Micrometerscitations
- 2015Large volume serial section tomography by Xe Plasma FIB dual beam microscopycitations
- 2014Correlative tomographycitations
- 2013Simultaneous measurement of X-ray powder diffraction and ferroelectric polarisation data as a function of applied electric field at a range of frequenciescitations
Places of action
| Organizations | Location | People |
|---|
document
Embedded 3D printing of Multi-material composites
Abstract
<jats:title>Abstract</jats:title><jats:p>Additive manufacturing could open new opportunities in the design and fabrication of advanced composites and devices incorporating multiple phases. However, when it comes to the combination of inorganic materials (ceramics and metals) it is difficult to achieve the degree of structural control demanded by many advanced applications. To address this challenge, we have developed a means of embedded printing to build complex, fine structures within dense ceramics. We have formulated a self-healing ceramic gel that enables the movement of a printing nozzle in its interior and that heals without defect after it has passed. Upon subsequent heat treatment, the gel forms a dense, defect-free ceramic that encapsulates the printed structure. We demonstrate the potential of the technique through two case studies. One is the printing of light, sacrificial graphite structures to introduce complex microchannel arrangements in a ceramic for applications such a thermal management. The other is to embed dense steel framework structures in aluminum oxide to increase its fracture resistance. The approach enables the introduction of auxetic structures that generate works of fracture 50% greater than those obtained with simple fibre arrays and that are orders of magnitude above the fracture energy of the ceramic. These results suggest that embedded 3D printing can open the way to implement new designs in ceramic matrix composites.</jats:p>