| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Małek, Marcin
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (14/14 displayed)
- 2023Empirical Study on the Effect of Tungsten Carbide Grain Size on Wear Resistance, Cutting Temperature, Cutting Forces and Surface Finish in the Milling Process of 316L Stainless Steelcitations
- 2019Analysis of the microstructure of an AZ31/AA1050/AA2519 laminate produced using the explosive-welding methodcitations
- 2017Effect of adding water-based binders on the technological properties of ceramic slurries based on silicon carbide citations
- 2016Investigation of the Basic Properties of Ceramic Proppants in Raw State Obtained by the Method of Mechanical Granulationcitations
- 2016Selecting key parameters of the green pellets and lightweight ceramic proppants for enhanced shale gas exploitationcitations
- 2016Investigation of key parameters influence on properties of the green pellets and lightweight ceramic proppants obtained by mechanical granulation method citations
- 2016Characterization and evaluation properties of ceramic proppants used in the extraction of the unconventional hydrocarbons
- 2016Rheological properties of alumina ceramic slurries for ceramic shell-mould fabricationcitations
- 2016Optimizing the Lightweight Ceramic Proppants Propertiescitations
- 2016Technological Properties of Ceramic Slurries Based on Silicon Carbide with Poly(vinyl alcohol) Addition for Shell Moluds Fabrication in Precision Casting Processcitations
- 2016Experimental ceramic proppants characterization in the process of shale gas extraction
- 2015Studies of the properties of green ceramic proppants obtained by spray drying method
- 2015Study of deflocculation of white clay for obtaining ceramic proppants fabrication in spray dryer
- 2015Influence of deflocculant addition on rheological properties of the slurries based on bauxite
Places of action
| Organizations | Location | People |
|---|
article
Rheological properties of alumina ceramic slurries for ceramic shell-mould fabrication
Abstract
This research is about the properties of ceramic slurries prepared from hydrous nano-alumina-based binder and a corundum matrix used for fabricating the prime coat of ceramic shell moulds. Solid-state alumina powders with different granulations were used. The modification of the technological properties of the prepared slurries was based on additions of a polyacrylic binder with different amounts of polymer with respect to the alumina for different powder ratios. The slurries were prepared and tested in a mechanical mixer. During the slurry preparation (within 96 h), the plate weight, Zahn cup 4# viscosity and dynamic viscosity were controlled. The morphology and chemical properties of corundum powders and polymer were characterized with SEM and powder-grain-size distribution. The obtained results of the corundum-based ceramic slurries indicate that the application of a polymeric binder with various concentrations based on nano-alumina oxides causes different properties in comparison to the other commonly used binders.