| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Gargarella, Piter
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (17/17 displayed)
- 2024Metal powder as feedstock for laser-based additive manufacturing: From production to powder modificationcitations
- 2023Effect of scanning strategy on microstructure and mechanical properties of a biocompatible Ti–35Nb–7Zr–5Ta alloy processed by laser-powder bed fusioncitations
- 2023Advanced characterization of bulk alloy and in-situ debris nanoparticles formed during wear of Fe–Nb–B ultrafine eutectic laser cladding coatings
- 2023Metal powder as feedstock for laser-based additive manufacturing: From production to powder modification
- 2022Effect of scanning strategy on microstructure and mechanical properties of a biocompatible Ti–35Nb–7Zr–5Ta alloy processed by laser-powder bed fusion
- 2022Effect of scanning strategy on microstructure and mechanical properties of a biocompatible Ti–35Nb–7Zr–5Ta alloy processed by laser-powder bed fusion
- 2022Effect of rotational speed and double-sided welding in friction stir–welded dissimilar joints of aluminum alloy and steelcitations
- 2022Laser remelting of AlSi10Mg(-Ni) alloy surfaces: influence of Ni content and cooling rate on the microstructure
- 2021Effect of the gap width in AZ31 magnesium alloy joints obtained by friction stir weldingcitations
- 2020Characterization of dissimilar friction stir welded lap joints of AA5083 and GL D36 steelcitations
- 2020Processing a biocompatible Ti-35Nb-7Zr-5Ta alloy by selective laser meltingcitations
- 2019Selective laser melting of Cu-based shape memory alloys
- 2018Microstructural characterization of a laser surface remelted Cu-based shape memory alloycitations
- 2015Structural evolution in Ti-Cu-Ni metallic glasses during heating
- 2015Phase formation, thermal stability and mechanical properties of a Cu-Al-Ni-Mn shape memory alloy prepared by selective laser meltingcitations
- 2015Phase separation in rapid solidified Ag-rich Ag-Cu-Zr alloyscitations
- 2014Phase formation, thermal stability and mechanical behaviour of TiCu-based alloys
Places of action
| Organizations | Location | People |
|---|
article
Phase formation, thermal stability and mechanical properties of a Cu-Al-Ni-Mn shape memory alloy prepared by selective laser melting
Abstract
Selective laser melting (SLM) is an additive manufacturing process used to produce parts with complex geometries layer by layer. This rapid solidification method allows fabricating samples in a non-equilibrium state and with refined microstructure. In this work, this method is used to fabricate 3 mm diameter rods of a Cu-based shape memory alloy. The phase formation, thermal stability and mechanical properties were investigated and correlated. Samples with a relative density higher than 92% and without cracks were obtained. A single monoclinic martensitic phase was formed with average grain size ranging between 28 to 36 μm. The samples exhibit a reverse martensitic transformation temperature around 106 ± 2 °C and a large plasticity in compression (around 15±1%) with a typical “double-yielding” behaviour. ; publishedVersion