| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Ahmad, Hilton
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2021Numerical Modelling of Foamed Concrete Beam under Flexural Using Traction-Separation Relationshipcitations
- 2020Open-Hole Kenaf Fiber Composites Under Elevated Temperatures: Experimental And Numerical Approaches
- 2020Strength predictions of single-lap woven fabric Kenaf composites bolted joints
- 2018Strength Predictions of Multi-Bolted Joints in Woven Fabric Kenaf Composite Plates with Different Configurations Using Xfem Frameworks
- 2018Three-dimensional Stress Analysis Study on Multi-Bolted Joints of Composite Platescitations
- 2017Stress distribution study on multi-holes configurations in woven fabric kenaf composite platescitations
- 2017XFEM modelling of open-hole woven fabric kenaf composite plates
- 2017Notched Strength of Woven Fabric Kenaf Composites with Different Fiber Orientationscitations
- 20173-D modelling of single-lap multi-bolted joints under quasi-static conditionscitations
- 2017Fracture Energy of Woven Fabric Kenaf Composite Plates with Different Fiber Orientations
- 2016Experimental Strength of Woven Fabric Kenaf Composite Plates with Different Stacking Sequencescitations
- 2016Experimental Strength of Single-Lap Hybrid Joints on Woven Fabric Kenaf Fiber Composites Under Quasi Static Conditioncitations
- 2016Notched Strength of Woven Fabric Kenaf Composite Plates with Different Stacking Sequences and Hole Sizescitations
- 2013Strength Prediction of Notched Woven Composite Plates Using a Cohesive Zone Approachcitations
- 2013Physically based finite element strength prediction in notched woven laminates under quasi-static loadingcitations
- 20123-D modelling of GFRP woven fabric double-lap bolted joint
Places of action
| Organizations | Location | People |
|---|
article
Strength predictions of single-lap woven fabric Kenaf composites bolted joints
Abstract
Application of woven fabric kenaf fibers in production of polymeric composites (known as woven fabric kenaf reinforced composite (WKRP)) were readily available in the literatures due to excellent tensile strength and elongation at break. Nevertheless, there are less reported work and information regarding to performance of these materials in bolted joints problem. Bolted joints demonstrate complicated damage morphologies either net-tension, shear-out or bearing failure modes dependence upon combination arrays of lay-up/joint variables. XFEM approach has been reported in the literature, yet the agreements are limited to net-tension failure resulting from stress concentration problem. The aim of this paper to carry out strength prediction work of single-lap WKRP/aluminium bolted joints by using Hashin formulation within 3D finite element framework. Hashin formulation which based on ply-by-ply basis seen to perform better prediction to bearing failure modes. The material properties incorporated within Hashin formulation was taken from a single-ply of woven fabric. Strength prediction from Hashin formulation showed a difference of less than ±25% in net tension-bearing failure mode, but less good predictions (some lay-up showed discrepancies of 50%) in smaller W/d to give net-tension mode. Good prediction in net-tension-bearing failure were exhibited in Hashin formulation than XFEM approach as bearing failure is based on ply-by-ply basis due to fiber kinking and matrix compression.