693.932 PEOPLE
| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Oechsner, Matthias
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (23/23 displayed)
- 2024Requirement-specific Adjustment ofResidual Stresses During Cold Extrusion
- 2024Investigation on surface characteristics of wall structures out of stainless steel 316L manufactured by laser powder bed fusioncitations
- 2024Empowering PVD for corrosion protectioncitations
- 2024Einfluss von Plastifizierung und Abkühlrate auf die Korrosionsbeständigkeit beim artgleichen Rührreibschweißen von EN AW-7020 und EN AW-7075 – Teil 1
- 2024Mechanistic insights into chemical corrosion of AA1050 in ethanol‐blended fuels with water contamination via phase field modeling
- 2024Mechanical Characterization Potentials of Aluminide Diffusion Coatings on Molybdenum Substrates
- 2024Calibration of the residual stresses with an active die during the ejection phase of cold extrusion
- 2024On the Monotonic and Cyclic Behavior of an Al‐Mg‐Zn‐Cu‐Si Compositionally Complex Alloy
- 2023Comparison of Cast, Wrought, and LPBF Processed IN718 Concerning Crack Growth Threshold and Fatigue Crack Growth Behaviorcitations
- 2023On the Monotonic and Cyclic Behavior of an Al‐Mg‐Zn‐Cu‐Si Compositionally Complex Alloycitations
- 2023Increase in residual lifetime due to low amplitude cycles and dwell times at room temperature: Observations and suspected mechanisms
- 2023Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testingcitations
- 2022Investigation of Material Properties of Wall Structures from Stainless Steel 316L Manufactured by Laser Powder Bed Fusioncitations
- 2022Robust determination of fatigue crack propagation thresholds from crack growth datacitations
- 2022Cooling rate as a process parameter in advanced roll forming to tailor microstructure,mechanical and corrosion properties of EN AW 7075 tubes
- 2021On the Influence of Control Type and Strain Rate on the Lifetime of 50CrMo4
- 2021On the Influence of the Microstructure upon the Fatigue and Corrosion Fatigue Behavior of UNS N07718
- 2021Calibration of the residual stresses with an active die during the ejection phase of cold extrusioncitations
- 2020On the Influence of Control Type and Strain Rate on the Lifetime of 50CrMo4citations
- 2020Application of Damage Mechanics and Polynomial Chaos Expansion for Lifetime Prediction of High-Temperature Components Under Creep-Fatigue Loadingcitations
- 2020Effect of Friction Stir Processing on Microstructural, Mechanical, and Corrosion Properties of Al-Si12 Additive Manufactured Componentscitations
- 2018Additive Manufacturing of Glass Components - Exploring the Potential of Glass Connections by Fused Deposition Modelingcitations
- 2014Influence of load signal form and variable amplitude loading on the corrosion fatigue behaviour of aluminium alloyscitations
Places of action
| Organizations | Location | People |
|---|
booksection
Requirement-specific Adjustment ofResidual Stresses During Cold Extrusion
Abstract
Residual stresses are considered critical to quality in conventional manufacturing strategies. This is where the DFG's Priority Program 2013 comes in, looking instead at the opportunities and possibilities for improving the properties of components by targeted use of residual stresses. In the years 2017 to 2023, research teams from all over Germany were able to prove the stability, controllability and usefulness of residual stresses in flat and solid forming manufacturing processes of metallic components. In addition, the cross-project working groups achieved many insights into the fundamental understanding, simulation and, in particular, industry-oriented measurement of residual stresses. The extensive results of these six years of research activities are presented in this final report.