| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Gundlach, Carsten
Technical University of Denmark
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (18/18 displayed)
- 2024Microstructure of additive manufactured materials for plasma-facing components of future fusion reactorscitations
- 2021The STRYDE limb lengthening nail is susceptible to mechanically assisted crevice corrosion:an analysis of 23 retrieved implantscitations
- 2021The STRYDE limb lengthening nail is susceptible to mechanically assisted crevice corrosion: an analysis of 23 retrieved implantscitations
- 2021The STRYDE limb lengthening nail is susceptible to mechanically assisted crevice corrosioncitations
- 2021Microstructure‐dependent corrosion of herringbone‐grooved embossed Al–1.1 wt% Mn strips for heat exchanger tubescitations
- 2021Characterization of high frequency welded aluminium microfin tube for heat exchangerscitations
- 2021Rheological characterization of 3D printable geopolymerscitations
- 2020Highly structured 3D pyrolytic carbon electrodes derived from additive manufacturing technologycitations
- 2019Effect of scanning strategy during selective laser melting on surface topography, porosity, and microstructure of additively manufactured Ti-6Al-4Vcitations
- 2019Effect of scanning strategy during selective laser melting on surface topography, porosity, and microstructure of additively manufactured Ti-6Al-4Vcitations
- 2019Process characterization for molding of paper bottles using computed tomography and structure tensor analysis
- 2018Determination of the fibre orientation distribution of a mineral wool network and prediction of its transverse stiffness using X-ray tomographycitations
- 2018Internal Fiber Structure of a High-Performing, Additively Manufactured Injection Molding Insertcitations
- 2017Graphite nodules in fatigue-tested cast iron characterized in 2D and 3Dcitations
- 2017Crack Tip Flipping under Mode I Tearing: Investigated by X-Ray Tomographycitations
- 2012Synchrotron diffraction analysis of retained austenite in welded transformation induced plasticity (TRIP) steelscitations
- 2006Recovery in aluminium
- 2004Metal Microstructures in Four Dimensions
Places of action
| Organizations | Location | People |
|---|
article
Synchrotron diffraction analysis of retained austenite in welded transformation induced plasticity (TRIP) steels
Abstract
A quantitative analysis of the retained austenite (RA) fractions in gas tungsten arc welded silicon and aluminium containing transformation induced plasticity steels was carried out by synchrotron X-ray diffraction measurements. The variation in RA transverse to the weld line was measured to study the effect of weld thermal cycles on the stabilisation of austenite in the heat affected zone (HAZ) and the fusion zone (FZ). The results showed that the FZ of silicon based steels contained a higher amount of RA (~7%) than aluminium based steels, which contained only ~4%. During the solidification of the weld pool, aluminium was found to partition to solidifying d-ferrite and to stabilise the soft d-ferrite grains at the fusion boundaries. Owing to this partitioning, the HAZ was enriched in carbon and the RA content was found to increase with distance from the fusion boundaries. In contrast, this partitioning behaviour was not present in silicon based transformation induced plasticity steels and a lesser amount of RA was found in the coarse grained HAZ than in the FZ. © 2012 Institute of Materials, Minerals and Mining.