| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
El Mehtedi, Mohamad
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (32/32 displayed)
- 2024Feasibility Study of Solid-State Recycling through Direct Hot Rolling of AA5754 Aluminum Chips for Automotive Applicationscitations
- 2024Life cycle assessment (LCA) of a novel solid-state recycling process for aluminum alloy AA6063 chips via direct hot rollingcitations
- 2024Innovative Solid-State Recycling of Aluminum Alloy AA6063 Chips Through Direct Hot Rolling Process
- 2024Effect of post heat treatment on microstructure and mechanical properties of hot-rolled AA2017 aluminum alloycitations
- 2024Effect of Temperature and Strain on Bonding of Similar AA3105 Aluminum Alloys by the Roll Bonding Processcitations
- 2021Assessment of drilling-induced delamination and tool wear in carbon fibre reinforced laminatescitations
- 2021Bonding of similar AA3105 aluminum alloy by Accumulative Roll Bonding processcitations
- 2019High temperature deformation of IN718 superalloy: use of basic creep modelling in the study of Nickel and single-phase Ni-based superalloyscitations
- 2019Flow curve prediction of ZAM100 magnesium alloy sheets using artificial neural network-based modelscitations
- 2018Effect of cold rolling on the mechanical properties and formability of FSWed sheets in AA5754-H114citations
- 2018Effect of the Rolling Temperature on Hot Formability of ZAM100 Magnesium Alloycitations
- 2018In-process Control of Rotational Speed in Friction Stir Welding of Sheet Blanks with Variable Mechanical Propertiescitations
- 2017Mechanical properties of cold rolled friction stir welded sheets in AA5754 aluminium alloy
- 2017Tool wear and hole quality in drilling of CFRP/AA7075 stacks with DLC and nanocomposite TiAlN coated toolscitations
- 2016Microstructural and constitutive analysis in process modeling of hot working: the case of a Mg-Zn-Mn alloycitations
- 2016Investigation on process parameters affecting blanking of AISI 1006 low carbon steelcitations
- 2015Characterization of hot deformation of CW602N brasscitations
- 2015The search for reliable inputs in modelling hot working operations: a model describing the flow behavior of metals at high temperature applied to CW602N brass
- 2014A New Constitutive Model Describing the Plastic Flow of Metals: Application to the AA6082 Aluminum Alloycitations
- 2014High temperature processing of brass: Constitutive analysis of hot working of Cu-Zn alloyscitations
- 2014A new constitutive model for the plastic flow of metals at elevated temperaturescitations
- 2014Hot workability in process modeling of a bearing steel by using combined constitutive equations and dynamic material modelcitations
- 2013High temperature deformation and microstructural instability in AZ31 magnesium alloycitations
- 2013Prediction Models of the final properties of steel rods obtained by thermomechanical rolling process
- 2013Grain evolution analysis and experimental validation in the extrusion of 6XXX alloys by use of a lagrangian FE codecitations
- 2012High temperature mechanical properties of an aluminum alloy containing Zn and Mgcitations
- 2012High Temperature Creep and Superplasticity in a Mg–Zn–Zr Alloycitations
- 2011Analysis of the effect of friction stir welding on the minimum creep rate of an Mg–3% Al–1% Zn alloycitations
- 2010Influence of data conversion methods from torsion tests on the Garofalo equation parameters for a high nitrogen steelcitations
- 2009Microstructure-related equations for the constitutive analysys of creep in magnesium alloyscitations
- 2007Analysis of high-temperature deformation and microstructure of an AZ31 magnesium alloycitations
- 2004HOT WORKING AND MULTIPASS DEFORMATION OF A 41CR4 STEEL
Places of action
| Organizations | Location | People |
|---|
article
Assessment of drilling-induced delamination and tool wear in carbon fibre reinforced laminates
Abstract
<jats:p> A highly accurate X-ray damage characterization technique was used in this study to investigate the correlation between hole damage, tool wear and thrust force in drilling of carbon fibre reinforced laminates. Woven carbon/epoxy panels were drilled with a twist tool for 592 holes and the internal damage induced by drilling was investigated by high-resolution penetrant-enhanced X-radiography for comparison with damage evaluated by visual inspection. The study shows that the dominant damage mode induced by drilling is delamination and that tool wear has a significant effect on the size of the delaminated area. The analyses also show that the delaminated areas estimated by visual inspection are much smaller than those identified by X-radiography. This finding indicates that visual observation techniques may provide dangerously unconservative indications and should be used in association with more reliable damage evaluation methods to assess the hole quality of drilled carbon fibre reinforced composites. </jats:p>