| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Noster, Ulf
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (20/20 displayed)
- 2024Effect of Carbon Content on the Phase Composition, Microstructure and Mechanical Properties of the TiC Layer Formed in Hot-Pressed Titanium-Steel Compositescitations
- 2024Preparation methodology for the microstructural characterization of diffusion layers in a titanium/steel composite
- 2023Influence of carbon content on the formation of TiC at diffusion bonded titanium-steel interface
- 2023Quasi-in-Situ Analysis of Electropolished Additively Manufactured Stainless Steel Surfaces
- 2023Enhancement of laser cut edge quality of ultra-thin titanium grade 2 sheets by applying in-process approach using modulated Yb:YAG continuous wave fibre laser
- 2022On the nanoindentation behavior of a TiC layer formed through thermo-reactive diffusion during hot pressing of Ti and cast ironcitations
- 2021An Integrative Experimental Approach to Design Optimization and Removal Strategies of Supporting Structures Used during L-PBF of SS316L Aortic Stentscitations
- 2020Computational analysis of the effects of geometric irregularities and post-processing steps on the mechanical behavior of additively manufactured 316L stainless steel stentscitations
- 2020Mechanical properties of small structures built by selective laser melting 316 L stainless steel – a phenomenological approach to improve component designcitations
- 2008Flame sprayed Al-12Si coatings for the improvement of the adhesion of composite casting profilescitations
- 2008Finite element based optimization of a novel metal-composite-joint
- 2008Effect of Deep Rolling on the Cyclic Performance of Magnesium and Aluminium Alloys in the Temperature Range 20-250°C
- 2007The InnMag project - Processing Mg for civil aircraft applicationcitations
- 2006Mechanical Behavior and Residual Stresses in AZ31 Wrought Magnesium Alloy Subjected to Four Point Bendingcitations
- 2005Residual stress relaxation and cyclic deformation behavior of deep rolled AlMg4.5Mn (AA5083) at elevated temperaturescitations
- 2003On the influence of mechanical surface treatments—deep rolling and laser shock peening—on the fatigue behavior of Ti–6Al–4V at ambient and elevated temperaturescitations
- 2003Isothermal Fatigue Behavior and Residual Stress States of Mechanically Surface Treated Ti-6Al-4V: Laser Shock Peening vs. Deep Rollingcitations
- 2003High Temperature Fatigue of Mechanically Surface Treated Materialscitations
- 2003On the fatigue behavior and associated effect of residual stresses in deep rolled and laser shock peened Ti-6Al-4V at ambient and elevated temperatures
- 2003Verhalten laserschockverfestigter und festgewalzter Randschichten der Ti‐Legierung Ti‐6Al‐4V bei schwingender Beanspruchung unter erhöhten Temperaturencitations
Places of action
| Organizations | Location | People |
|---|
article
Quasi-in-Situ Analysis of Electropolished Additively Manufactured Stainless Steel Surfaces
Abstract
Progress in additive manufacturing is leading to the emergence of new areas of application. Laser Powder Bed Fusion (L-PBF) is increasingly used for the development of metallic medical implants, but for high-risk implants like vascular support structures (stents), surface quality is critical to ensure successful implantation without harming the surrounding tissue and ensure the patients’ health. Therefore, enhancing the surface quality is crucial. Electropolishing is a method for removing surface roughness by smoothing out micro-peaks and valleys. However, L-PBF structures have a high surface roughness due to metal particles adhering on the surface. To achieve a smooth surface for additively manufactured implants like stents using electropolishing, the removal of these particles needs to be studied in more detail. The objective of this study is to examine the electropolishing mechanism of 316L stainless steel samples additively manufactured through Laser Powder Bed Fusion (L-PBF). The main objective is to investigate the removal properties and surface characteristics during electropolishing. To achieve this, various surfaces were characterized for morphology and roughness during Hull cell experiments. Markings are utilized on the Hull cell sample surfaces to identify points of interest during quasi-in-situ measurements. The surfaces are then analyzed after multiple time steps, applying different currents to investigate particle dissolution. The surface characteristics are analyzed through scanning electron microscopy, and surface roughness is analyzed using laser scanning microscopy. The results show that the electropolishing process preferentially removes the adhering particles present on the surface of the samples. Increasing the current density results in faster particle dissolution and a smoother surface (see Figure 1a and b). The mechanism of material removal of various surface features, as shown in Figure 1 (red circle, yellow arrow and red square), was assessed based on the experimental results of the ...