| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Hinduja, Srichand
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (14/14 displayed)
- 2021A Review on Microcellular Injection Mouldingcitations
- 2010Image processing methods for online measurement in radial-axial ring rolling
- 2009Investigating the feasibility of DLC-coated twist drills in deep-hole drillingcitations
- 2006Effect of MQL on the tool life of small twist drills in deep-hole drillingcitations
- 2006Boundary element stress analysis for bi-metallic dies in pressure diecastingcitations
- 2006Boundary element stress analysis for copper-based dies in pressure die castingcitations
- 2006Bi-metallic dies for rapid die castingcitations
- 2006Experimental investigation into the thermal behavior of copper-alloyed dies in pressure die castingcitations
- 2006The performance of small diameter twist drills in deep-hole drillingcitations
- 2002Optimization for boiling heat transfer determination and enhancement in pressure die castingcitations
- 2001Novel cooling channel shapes in pressure die castingcitations
- 2000An experimental and numerical investigation into the thermal behavior of the pressure die casting processcitations
- 2000Determination of heat transfer coefficients using a 1-d flow model applied to irregular shaped cooling channels in pressure diecastingcitations
- 2000Predicting heat extraction due to boiling in the cooling channels during the pressure die casting processcitations
Places of action
| Organizations | Location | People |
|---|
article
An experimental and numerical investigation into the thermal behavior of the pressure die casting process
Abstract
The modeling of the pressure die casting process generally requires the specification of heat transfer coefficients at the surfaces of the die. The coefficients at the cavity-casting interface and at the cooling channel surfaces are of particular importance. In order to provide estimates for these heat transfer coefficients, the behavior of a specifically designed zinc alloy casting is investigated using a three dimensional thermal model whose predictions are supported by experimentally obtained results. The numerical model uses the boundary element method for the dies, as surface temperatures are of particular importance, and the finite element method for the casting, where the nonlinear material behavior makes this technique suitable. The experimental data comprises of thermocouple measurements of both die, casting, and coolant temperatures for three sets of operating conditions. These measurements are complemented by qualitative data of casting defects caused by incomplete solidification and thermal imaging temperature measurements. An experimental technique for obtaining average heat transfer coefficients for the casting-die interface is presented. Although the technique circumvents the need to place thermocouples in the casting and provides average heat transfer coefficients of sufficient accuracy for modeling purposes, it is not sufficiently responsive to provide accurate transient information. The presence of coolant boiling is detected by its effect on the rates of heat extraction. Heat transfer coefficients are determined for the cooling channels using a boiling model. Comparison between predicted and experimental rates of heat transfer to the coolant support the need for a boiling model. Good agreement is obtained between experimental and numerical predictions.