| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Somers, Nicolas
University of Liège
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (15/15 displayed)
- 2024Rapid, Direct Fabrication of Thermochromic Ceramic Composite Sensors via Flash Lamp Annealing
- 2024Infrared irradiation to drive phosphate condensation as a route to direct additive manufacturing of oxide ceramicscitations
- 2023Mg2+, Sr2+, Ag+, and Cu2+ co‐doped β‐tricalcium phosphate: Improved thermal stability and mechanical and biological propertiescitations
- 2023Fabrication of doped β-tricalcium phosphate bioceramics by Direct Ink Writing for bone repair applicationscitations
- 2023Infrared Irradiation to Drive Phosphate Condensation as a Route to Direct Additive Manufacturing of Oxide Ceramicscitations
- 2023Synthesis and Direct Ink Writing of doped β-tricalcium phosphate bioceramics for bone repair applications
- 20233D printing of doped β-tricalcium phosphate bioceramics using robocasting
- 2022Fabrication of doped β-tricalcium phosphate bioceramics by Direct Ink Writing for bone repair applicationscitations
- 2022Young Ceramists in the Spotlight
- 2022Fabrication of doped b-tricalcium phosphate bioceramics by robocasting for bone repair applications
- 2022Fabrication of doped b-tricalcium phosphate bioceramics by robocasting for bone repair applications
- 2021Fabrication of higher thermal stability doped β-tricalcium phosphate bioceramics by robocasting
- 2021Influence of dopants on thermal stability and densification of β-tricalcium phosphate powderscitations
- 2021Development of calcium phosphate suspensions suitable for the stereolithography processcitations
- 2020Fabrication of higher thermal stability doped β-tricalcium phosphate bioceramics by robocasting
Places of action
| Organizations | Location | People |
|---|
article
Infrared Irradiation to Drive Phosphate Condensation as a Route to Direct Additive Manufacturing of Oxide Ceramics
Abstract
<jats:title>Abstract</jats:title><jats:p>This paper introduces a fast, low‐temperature, pressureless process to chemically bind ceramic parts with the help of infrared irradiation and phosphate binder condensation. Ceramic components are synthesized from slurries of ceramic powders and Al(H<jats:sub>2</jats:sub>PO<jats:sub>4</jats:sub>)<jats:sub>3</jats:sub> binder that are irradiated with short‐waved infrared light capable of heating the system to 350°C. This irradiation is found to be sufficient to drive phosphate condensation, binding the ceramic powders together within a matter of seconds. The IR irradiated components show an increase in density and Vickers hardness. Layer‐by‐layer spraying and irradiation is demonstrated as a route to additive manufacturing using various ceramic chemistries. While further optimization is needed to control desired microstructure, this process of using chemically bonded ceramic binders with IR heating for additive manufacturing shows the potential to find applications in various ceramic systems, including refractories, bone implants, electronics, and thermal barriers coatings.</jats:p><jats:p>This article is protected by copyright. All rights reserved</jats:p>