| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Lassila, Lippo
University of Turku
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (8/8 displayed)
- 2023Load‐bearing capacity and wear characteristics of short fiber‐reinforced composite and glass ceramic fixed partial denturescitations
- 2023Fiber-reinforced composites in dentistry – An insight into adhesion aspects of the material and the restored tooth constructcitations
- 2021Effect of Fiber Reinforcement Type on the Performance of Large Posterior Restorations: A Review of In Vitro Studiescitations
- 2020Incorporation of cellulose fiber in glass ionomer cementcitations
- 2018Cellulose Fibre-Reinforced Biofoam for Structural Applicationscitations
- 2017Bending Properties of Fiber-Reinforced Composites Retainers Bonded with Spot-Composite Coveragecitations
- 2017Cellulose fibre-reinforced biofoam for structural applicationscitations
- 2015Effects of nanofillers on mechanical properties of fiber-reinforced composites polymerized with light-curing and additional postcuringcitations
Places of action
| Organizations | Location | People |
|---|
article
Load‐bearing capacity and wear characteristics of short fiber‐reinforced composite and glass ceramic fixed partial dentures
Abstract
<jats:title>Abstract</jats:title><jats:p>The aim of this study was to evaluate load‐bearing capacity and wear performance of experimental short fiber‐reinforced composite (SFRC) and conventional lithium‐disilicate CAD/CAM fabricated fixed partial dentures (FPDs). Two groups (<jats:italic>n</jats:italic> = 12/group) of three‐unit CAD/CAM fabricated posterior FPDs were made. The first group used experimental SFRC blocks, and the second group fabricated from lithium‐disilicate (IPS e.max CAD). All FPDs were luted on a zirconia testing jig with dual‐curing resin cement. Half of FPDs per group were quasi‐statically loaded until fracture. The other half experienced cyclic fatigue aging (100.000 cycles, Fmax = 500 N) before loading quasi‐statically until fracture. Fracture mode was examined using SEM. Wear test was performed using 15,000 loading cycles. Both material type and aging had a significant effect on the load‐bearing capacity of FPDs. Experimental SFRC CAD without fatigue aging had significantly the highest load‐bearing capacity (2096 ± 149N). Cyclic fatigue aging decreased the load‐bearing capacity of the SFRC group (1709 ± 188N) but increased it for the lithium‐disilicate group (1546 ± 155N). Wear depth values of SFRC CAD (29.3μm) were significantly lower compared to lithium‐disilicate (54.2μm). Experimental SFRC CAD demonstrated the highest load‐bearing capacity before and after cyclic fatigue aging, and superior wear behavior compared to the control material.</jats:p>