| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Flynn, David
Heriot-Watt University
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (25/25 displayed)
- 2023Role of interface in optimisation of polyamide-6/Fe3O4 nanocomposite properties suitable for induction heating.citations
- 2023Role of interface in optimisation of polyamide-6/Fe3O4 nanocomposite properties suitable for induction heatingcitations
- 2022Quantification of wear in glass reinforced epoxy resin composites using surface profilometry and assessing effect of surfacing film involvementcitations
- 2021A Review of Sensing Technologies for Non-Destructive Evaluation of Structural Composite Materialscitations
- 2020Analysis of throwing power for megasonic assisted electrodeposition of copper inside THVscitations
- 2018Nanocomposite-Based Microstructured Piezoresistive Pressure Sensors for Low-Pressure Measurement Rangecitations
- 2018Analysis of Sandstone Pore Space Fluid Saturation and Mineralogy Variation via Application of Monostatic K-Band Frequency Modulated Continuous Wave Radarcitations
- 2018Copper electroplating of PCB interconnects using megasonic acoustic streamingcitations
- 2018A digitally-driven Hybrid Manufacturing process for the flexible production of engineering ceramic components
- 2017Analysis of geomaterials using frequency-modulated continuous wave radar in the K-band
- 2016Megasound Acoustic Surface Treatment Process in the Printed Circuit Board Industrycitations
- 2014Integration of Microfluidic Channels with Frequency Selective Surfaces for Sensing and Tuningcitations
- 2013Electroplating for high aspect ratio vias in PCB manufacturing: enhancement capabilities of acoustic streamingcitations
- 2013Microstructure formation in a thick polymer by electrostatic-induced lithographycitations
- 2013Electroplating for high aspect ratio vias in PCB manufacturing: Enhancement capabilities of acoustic streamingcitations
- 2012Electrodeposition of copper into high aspect ratio PCB micro-via using megasonic agitation
- 2011Investigation of high speed micro-bump formation through electrodeposition enhanced by megasonic agitationcitations
- 2011Innovative manufacturing and 3-dimensional packaging methods of micro ultrasonic transducers for medical applications
- 2011Design, Manufacturing and Packaging of High Frequency Micro Ultrasonic Transducers for Medical Applications
- 2010Influence of pulse reverse plating on the properties of Ni-Fe thin filmscitations
- 2010Bespoke interconnect technologies for optoelectronic and biomedical products
- 2009Design, fabrication, and characterization of flip-chip bonded microinductorscitations
- 2009Design methodology and fabrication process of a microinductor for the next generation of DC-DC power converterscitations
- 2009High density indium bumping using electrodeposition enhanced by megasonic agitationcitations
- 2006Assessment of microinductors for DC-DC converters
Places of action
| Organizations | Location | People |
|---|
document
Assessment of microinductors for DC-DC converters
Abstract
<p>There are increasing demands on the power density and efficiency of DC-DC power converters due to the soaring functionality and operational longevity required for today's electronic products. In addition, DC-DC converters are required to operate at new elevated frequencies in the MHz frequency regime. Typical ferrite cores, whose useable flux density falls drastically at these frequencies, have to be replaced and a method of producing compact component windings developed. In this study, two types of microinductors, pot-core and solenoid, for DC-DC converter applications have been analyzed for their performance in the MHz frequency range. The inductors were manufactured using an adapted UV-LIGA process and included electrodeposited nickel-iron and the commercial alloy Vitrovac 6025 as core materials. Using a vibrating sample magnetometer (VSM) and a Hewlett Packard 41 92A LFimpedance analyzer, the inductor characteristics such as power density, efficiency, inductance and Q-factor were recorded. Experimental, finite element and analytical results were used to assess the suitability of the magnetic materials and component geometries for low MHz operation. ©2006 IEEE.</p>