| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Kwame, James
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (11/11 displayed)
- 2021Effect of machining induced microstructure changes on the edge formability of titanium alloys at room temperature
- 2021Influence of longitudinal scratch defects on the bendability of titanium alloycitations
- 2020Influence of sheet conditions on in-plane strain evolution via ex-situ tensile deformation of Ti-3Al-2.5V at room temperaturecitations
- 2020Examining failure behaviour of commercially pure titanium during tensile deformation and hole expansion testcitations
- 2020Impact of machining induced surface defects on the edge formability of commercially pure titanium sheet at room temperaturecitations
- 2019Superplasticity of Ti-6Al-4V Titanium Alloy: Microstructure Evolution and Constitutive Modellingcitations
- 2019Superplastic deformation behavior of ultra-fine-grained Ti-1V-4Al-3Mo alloycitations
- 2019Experimental, modelling and simulation of an approach for optimizing the superplastic forming of Ti-6%Al-4%V titanium alloycitations
- 2019Effect of edge conditions on the formability of commercially pure titanium sheet (Grade 2) at room temperature
- 2017Superplastic deformation behaviour and microstructure evolution of near-α Ti-Al-Mn alloycitations
- 2017Modelling of the superplastic deformation of the near-a titanium alloy (Ti-2.5AL-1.8MN) using arrhenius-type constitutive model and artificial neural networkcitations
Places of action
| Organizations | Location | People |
|---|
article
Superplastic deformation behavior of ultra-fine-grained Ti-1V-4Al-3Mo alloy
Abstract
This paper studies the superplasticity of conventional sheets of Ti-1V-4Al-3Mo (α+β) alloy. The flow behavior was investigated in a temperature range of 775 °C–900 °C and a constant strain rate range of 2×10<sup>−4</sup>–5×10<sup>−3</sup> s−1 via uniaxial tensile tests. The microstructure evolution during the superplastic deformation was analyzed. The results revealed that, the flow behavior of Ti-1V-4Al- 3Mo (α+β) alloy is characterized by strain softening phenomena. The experimental stress-strain data were used to build a power law constitutive model. A processing map, which shows the safe and unsafe regions of deformation, was also constructed for the studied alloy. The optimal deformation regime was attained at a temperature of 875 °C and strain rate of 1×10<sup>−3 </sup>s<sup>−1</sup> which provided a β phase fraction of 52%. Equiaxed fine-grained α and β structure with size of2–3 μm as well as dislocation activity inside the α-grains were identified in the optimum deformation regime.