| People | Locations | Statistics |
|---|---|---|
| Naji, M. |
| |
| Motta, Antonella |
| |
| Aletan, Dirar |
| |
| Mohamed, Tarek |
| |
| Ertürk, Emre |
| |
| Taccardi, Nicola |
| |
| Kononenko, Denys |
| |
| Petrov, R. H. | Madrid |
|
| Alshaaer, Mazen | Brussels |
|
| Bih, L. |
| |
| Casati, R. |
| |
| Muller, Hermance |
| |
| Kočí, Jan | Prague |
|
| Šuljagić, Marija |
| |
| Kalteremidou, Kalliopi-Artemi | Brussels |
|
| Azam, Siraj |
| |
| Ospanova, Alyiya |
| |
| Blanpain, Bart |
| |
| Ali, M. A. |
| |
| Popa, V. |
| |
| Rančić, M. |
| |
| Ollier, Nadège |
| |
| Azevedo, Nuno Monteiro |
| |
| Landes, Michael |
| |
| Rignanese, Gian-Marco |
|
Marsi, Noraini
in Cooperation with on an Cooperation-Score of 37%
Topics
Publications (16/16 displayed)
- 2021Dynamic mechanical analysis and morphology of petroleum-based and bio-epoxy foams with wood fillercitations
- 2021Compressive strength, sound absorption coefficient (SAC) and water absorption analysis of HDPE plastic waste reinforced polystyrene and Portland cement for lightweight concrete (LWC)citations
- 2021Bending strength analysis of HDPE plastic reinforced wood waste and thermoplastic polymer to replace ceramic tile compositescitations
- 2021Characterization of foam materials based on HDPE plastic waste for automotive seat application
- 2021Develop Interlocking Concrete Block Pavement from Portland Cement, Polystyrene and Bottom Ash on Pedestrian Roadcitations
- 2020The Mechanical Performance of Tile Based on Plastic Waste (PW) Mixed Wood Waste (MWW)citations
- 2020The Mechanical Performance of Pipe Based on Fiberglass Reinforced with Plastic Waste (FRPW) Compositescitations
- 2020Utilization of Banana (Musa Paradisiaca) Peel As Bioplastic for Planting Bag Application
- 2019Graphene Composite Blueberries based Pencil Lead act as Superhydrophobic Coating on Plastic Surfaces for Solar Application
- 2019Endurance of Renewable Polymer Composite to UV Irradiation
- 2018Dynamic Mechanical Thermal Analysis of Wood Polymer Composite Endurance to Prolonged Ultra Violet Irradiation Exposurecitations
- 2016Ballistic Impact Response of Woven Hybrid Coir/Kevlar Laminated Compositescitations
- 20153C-SiC-on-Si based MEMS packaged capacitive pressure sensor operating up to 500 ºC and 5 MPacitations
- 2015The Mechanical Characterization of Bending Test for MEMS Capacitive Pressure Sensor Based 3C-SiC in High Temperaturecitations
- 2014Development of high temperature resistant of 500 °C employing silicon carbide (3C-SiC) based MEMS pressure sensorcitations
- 2013Biopolymer Doped with Titanium Dioxide Superhydrophobic Photocatalysis as Self-Clean Coating for Lightweight Compositecitations
Places of action
| Organizations | Location | People |
|---|
article
The Mechanical Performance of Pipe Based on Fiberglass Reinforced with Plastic Waste (FRPW) Composites
Abstract
<jats:title>Abstract</jats:title><jats:p>The project research present the mechanical performance of pipe based on fiberglass reinforced with plastic waste (FRPW) in plant application system. The use of FRPW able to reduce corrosion problem faced by oil and gas industry. In this study involved four types of combination ratio of fiberglass reinforced with plastic waste (FRPW) of 1.0: 0.5; 1.0:1.0; 1.0:1.5; and 1.0:2.0. The fabrication process started with grinding process of plastic waste into small size in the range of 0.1 mm. Fiberglass then reinforced with plastic waste by mixed with resin and hardener with ratio of 2: 1 and poured into the cylinder mould. There is a possibility fiberglass from 10-40% by weight result in substantial increase in elastic modulus, accompanied by an increase in strength with reduced ductility 1.0 of ratio. The tensile test showed clearly exhibited that 1.0 of plastic waste reinforced fiberglass with stand the higher maximum force value of 2.69 kN. For the bending test ratio of 1.0 of plastic waste withstand the higher bending strength at 5.29 kN. Ratio of 1.0 FRPW is more suitable for produced pipe in plant application system due to matrix-reinforcement bonding for each pipe sample after conducting tensile strength. The result obtained that ratio 1.0 of FRPW shown good matrix-reinforcement bonding.</jats:p>